In the field of precision manufacturing, investment casting is widely utilized for producing complex and high-integrity components, particularly in aerospace applications where stringent requirements for structural strength and sealing performance are paramount. However, the process is susceptible to various defects, with hot tearing being a critical issue that leads to significant scrap rates. This article, based on my extensive experience and research, delves into the analysis and resolution of hot tearing defects in iron pump casings produced via investment casting. I will explore the underlying mechanisms, employ numerical simulation techniques, and propose effective solutions, all while emphasizing the intricacies of investment casting.
Hot tearing, or hot cracking, occurs during the solidification process when the casting material is in a semi-solid state, characterized by low strength and ductility. As the casting contracts, thermal stresses develop due to constrained shrinkage, and if these stresses exceed the material’s strength at that temperature, cracks initiate along grain boundaries. In investment casting, the ceramic shell provides a rigid mold that can exacerbate these constraints, making hot tearing a common challenge. The focus here is on a specific pump casing made of a special cast iron, where hot tearing defects were observed at a high rejection rate, necessitating a thorough investigation.

The pump casing component, as analyzed in this study, is an aerospace part requiring excellent密封性 and mechanical properties. Its geometry, with an average wall thickness of 5 mm and overall dimensions of 116 mm × 103 mm × 60 mm, presents typical challenges in investment casting due to uniform thin sections that can cool rapidly, leading to thermal gradients. The material is a special cast iron, with its chemical composition detailed in Table 1. This alloy is chosen for its balance of strength and castability, but it is prone to hot tearing under certain conditions, as observed in the initial production runs.
| Element | C | Si | Mn | Cr | P | S |
|---|---|---|---|---|---|---|
| Content | 3.00-3.50 | 1.80-2.50 | 0.50-0.90 | 0.25-0.55 | 0.20-0.60 | <0.12 |
The investment casting process for this pump casing involved using an ethyl silicate binder with quartz flour and sand as refractory materials to build the ceramic shell. The shell thickness was approximately 8 mm. After dewaxing, the shell was fired at 900-950°C for 3 hours and then immediately poured at a temperature of 1350°C. The initial gating system design, as shown in the digital model, featured a relatively large sprue and runners, which contributed to the issues observed. Post-casting inspection revealed cracks primarily at the flange edges and cylindrical walls, with a reject rate of around 60%. Metallographic analysis confirmed these as hot tears, characterized by intergranular propagation and曲折 morphology.
To understand the root cause, I employed numerical simulation using ProCAST, a powerful tool for analyzing casting processes. The simulation setup involved creating a detailed model of the casting, ceramic shell, and sand box to replicate实际 conditions. Mesh generation was critical for accuracy; I used MeshCAST to create tetrahedral meshes with a size of 2 mm for the casting and shell, and 20 mm for the sand box, resulting in approximately 1.25 million elements. The thermophysical properties of the cast iron were derived from the chemical composition using the Scheil equation, which accounts for non-equilibrium solidification. The key parameters are summarized in Table 2 and used in subsequent calculations.
| Parameter | Value | Description |
|---|---|---|
| Liquidus Temperature, $T_L$ | 1200.2°C | Calculated via Scheil model |
| Solidus Temperature, $T_S$ | 954.3°C | Calculated via Scheil model |
| Density, $\rho$ | 7100 kg/m³ (liquid), 7500 kg/m³ (solid) | Temperature-dependent function |
| Specific Heat, $C_p$ | 750 J/kg·K (average) | Varies with temperature |
| Thermal Conductivity, $k$ | 40 W/m·K (liquid), 35 W/m·K (solid) | Temperature-dependent function |
| Young’s Modulus, $E$ | 120 GPa at room temperature, decreasing with temperature | Used in stress analysis |
| Yield Strength, $\sigma_y$ | Low at high temperatures, increasing during cooling | Critical for hot tearing |
The boundary conditions were set to mirror the actual investment casting process: pouring temperature of 1350°C, shell and sand preheat temperature of 900°C, interfacial heat transfer coefficients of 1000 W/m²·K between casting and shell, and 400 W/m²·K between shell and sand. The stress analysis utilized an elasto-plastic model, coupling filling, solidification, and stress calculations. The simulation aimed to capture the thermal gradients and stress development during solidification, which are pivotal in investment casting defects.
The results from ProCAST revealed significant insights into the hot tearing mechanism. The average normal stress distribution showed compressive stresses at the pump casing edges and tensile stresses along the cylindrical walls, correlating with the crack locations. The stress evolution over time indicated that the thin sections of the casing solidified first, experiencing tensile stresses early in the process, while the thicker gating system solidified later. This disparity in cooling rates and solidification times created a so-called “stress frame” effect, where the casting and gating system acted as constrained members, amplifying thermal stresses. The stress difference between critical points, such as the flange edge and sprue, was quantified using the following relation derived from thermal contraction:
$$ \Delta \sigma = E \cdot \alpha \cdot \Delta T \cdot f(\text{geometry}) $$
where $\Delta \sigma$ is the stress difference, $E$ is Young’s modulus, $\alpha$ is the coefficient of thermal expansion, $\Delta T$ is the temperature gradient, and $f(\text{geometry})$ accounts for the geometrical constraints inherent in investment casting molds. For the initial gating design, the solidification time of the sprue was simulated to be 1298 seconds, much longer than that of the casing walls, exacerbating the stress frame. The stress at key locations over time is plotted in Figure 1, showing that the flange edge transitioned from tension to compression, while the sprue remained under tension for an extended period, increasing the risk of hot tearing.
To further analyze the cooling behavior, I derived a simplified model for cooling rate in investment casting. The cooling rate $R_c$ can be expressed as:
$$ R_c = \frac{dT}{dt} = \frac{k}{\rho C_p} \cdot \frac{\partial^2 T}{\partial x^2} + \text{boundary effects} $$
where $k$ is thermal conductivity, $\rho$ is density, $C_p$ is specific heat, and $x$ is the spatial coordinate. In investment casting, the ceramic shell’s insulating properties modify this rate, leading to non-uniform cooling. The difference in cooling rates between the casing and gating system, $\Delta R_c$, was a critical factor, calculated as:
$$ \Delta R_c = R_{c,\text{casting}} – R_{c,\text{gating}} $$
For the initial design, $\Delta R_c$ was high, contributing to stress accumulation. The solidification time $t_s$ can be estimated using Chvorinov’s rule, adapted for investment casting:
$$ t_s = B \cdot \left( \frac{V}{A} \right)^n $$
where $V$ is volume, $A$ is surface area, $B$ is a mold constant dependent on shell properties, and $n$ is an exponent typically around 2. For the pump casing, with a high $A/V$ ratio due to thin walls, $t_s$ was short, while the gating system had a lower $A/V$ ratio and longer $t_s$. This mismatch is summarized in Table 3, highlighting the need for gating optimization in investment casting.
| Parameter | Initial Gating | Optimized Gating | Unit |
|---|---|---|---|
| Casing Cooling Rate, $R_{c,\text{casting}}$ | 15.2 | 14.8 | °C/s |
| Gating Cooling Rate, $R_{c,\text{gating}}$ | 5.1 | 8.3 | °C/s |
| Cooling Rate Difference, $\Delta R_c$ | 10.1 | 6.5 | °C/s |
| Casing Solidification Time, $t_{s,\text{casting}}$ | 45 | 48 | s |
| Gating Solidification Time, $t_{s,\text{gating}}$ | 1298 | 520 | s |
| Stress Difference at Critical Point, $\Delta \sigma$ | 85 | 45 | MPa |
Based on the simulation insights, I proposed an optimized gating design for the investment casting process. The key modification was reducing the size of the sprue and runners to minimize the cooling rate difference and solidification time disparity. This adjustment aimed to alleviate the stress frame effect by bringing the cooling curves of the casting and gating system closer together. The optimized gating system reduced the overall weight from 9.2 kg to 3.8 kg, improving yield without introducing other defects like shrinkage, thanks to the self-feeding characteristics of cast iron due to graphite expansion. The stress analysis for the optimized design showed a marked reduction in tensile stresses at the crack-prone areas, as depicted in the stress-time curves.
To validate the optimization, I conducted experimental trials with 40 castings using the revised investment casting工艺. The ceramic shells were prepared identically to before, and the pouring conditions remained unchanged. Post-casting inspection revealed no hot tearing defects, confirming the effectiveness of the solution. The absence of cracks demonstrated that reducing the gating system size in investment casting can successfully mitigate thermal stresses and prevent hot tearing. This outcome underscores the importance of balancing cooling rates in investment casting to control stress development.
The success of this approach can be generalized to other investment casting applications. Hot tearing in investment casting often stems from similar issues of thermal gradients and constrained shrinkage. By employing numerical simulation, designers can predict stress concentrations and optimize gating designs proactively. For instance, in investment casting of complex geometries, using multiple smaller gates instead of a single large one can distribute heat more evenly, reducing stress. Additionally, adjusting shell thickness or preheat temperature in investment casting can modulate cooling rates, offering further control over solidification behavior.
Beyond gating design, material properties play a crucial role in hot tearing susceptibility. For cast irons in investment casting, the graphite morphology influences the stress response. Flake graphite, as in gray iron, can provide some stress relief due to its lubricating effect, but in special cast irons with alloying elements, the behavior may differ. The yield strength at high temperatures, $\sigma_y(T)$, is particularly important, as hot tearing occurs when stress exceeds this value. A simplified criterion for hot tearing avoidance in investment casting can be formulated as:
$$ \sigma_{\text{thermal}}(T) < \sigma_y(T) \quad \text{for} \quad T \in [T_S, T_L] $$
where $\sigma_{\text{thermal}}(T)$ is the thermally induced stress. In investment casting, this stress is influenced by the mold restraint, which can be quantified by a restraint factor $R_f$:
$$ \sigma_{\text{thermal}} = E \cdot \alpha \cdot (T_0 – T) \cdot R_f $$
where $T_0$ is the initial temperature, and $R_f$ depends on the geometry and shell rigidity. For the pump casing, reducing the gating size decreased $R_f$ by lowering the stiffness of the stress frame.
In conclusion, this study highlights the effectiveness of numerical simulation in diagnosing and solving hot tearing defects in investment casting. Through detailed stress analysis using ProCAST, I identified that the cooling rate difference between the casting and gating system was the primary cause of thermal stresses leading to hot tearing. By optimizing the gating design to reduce this difference, the stress frame effect was mitigated, eliminating the defects in experimental trials. This approach not only improves quality but also enhances yield in investment casting processes. Future work could explore advanced materials modeling or real-time monitoring to further refine investment casting techniques for defect prevention.
The principles discussed here are applicable across various investment casting scenarios, emphasizing the need for integrated design and simulation. As investment casting continues to evolve for high-performance applications, understanding and controlling thermal stresses will remain critical. I recommend that practitioners in investment casting regularly employ simulation tools to optimize process parameters and gating designs, ensuring robust production of complex components like pump casings. This proactive strategy can significantly reduce scrap rates and improve efficiency in investment casting operations.
