Analysis and Countermeasures for Slag Inclusion Defects in Large Nodular Iron Crankshafts

In the production of large-scale nodular cast iron (NCI) crankshafts for diesel engines, the occurrence of slag inclusion defects has been a persistent and costly challenge, leading to significant scrap rates. This analysis details a systematic investigation into the root causes of these slag inclusion defects and the subsequent development of effective preventative measures based on extensive production statistics and targeted process experiments. Through methodical adjustments to key process parameters, the scrap rate attributed to slag inclusion was dramatically reduced.

I. Production Context and Initial Challenges

The initial manufacturing process for a critical diesel engine crankshaft involved melting iron in an acid-lined cupola. The typical pouring temperature ranged between 1280°C and 1320°C. The chemical composition targets for the base iron and the treated metal are summarized in Table 1.

<0.02

Table 1: Target Chemical Compositions (wt.%)
Material State C Si Mn P S Mgres REres
Base Iron 3.6-3.9 1.2-1.5 0.5-0.8 <0.10 <0.03 – –
Treated Iron (As-Cast) 3.5-3.8 2.4-2.8 0.5-0.8 <0.10 0.03-0.05 0.02-0.04

The nodularizing treatment employed a “plug” method. The inoculant alloy, with a composition of approximately 9% Mg, 5% Rare Earth (RE), 45% Si-Fe, and the balance being iron turnings, was melted and cast into a conical-shaped plug. The treatment process in the ladle followed these steps: 1) Tapping approximately 280 kg of iron, 2) Adding dehydrated sodium carbonate to the tap stream for desulfurization, 3) Performing initial slag-off, 4) Adding the Mg-RE plug using a pressure bell for nodularization, 5) A second slag-off followed by the addition of ~1 kg of crushed cryolite (Na3AlF6) as a slag conditioner, 6) A final slag-off before pouring, with an additional 0.5 kg of cryolite powder used to cover the metal surface in the ladle. Molding was done in dry sand molds, with two castings per mold.

Despite this established process, recurrent, batch-based slag inclusion defects resulted in scrap rates consistently above 10%. Spectrographic analysis of material from defect zones versus sound areas revealed elevated levels of Sulfur (S), Magnesium (Mg), and Rare Earths (RE) within the slag inclusions. This indicated that the slag inclusion defect likely comprised complex oxides, sulfides, and silicates of Mg and RE, alongside iron oxide (FeO).

II. Analysis of Factors Influencing Slag Inclusion Formation

1. Influence of Magnesium Addition

A primary suspect was the level of residual magnesium. High residual Mg increases the tendency for oxidation and dross formation. Experiments were conducted where the Mg content in the nodularizing alloy was systematically reduced while holding the RE addition constant. The results, shown in Table 2, demonstrate a clear correlation.

Table 2: Effect of Residual Magnesium on Slag Inclusion Severity
Nodularizer Mg (%) Avg. Residual Mg in Casting (%) Slag Inclusion Depth (mm) Remarks
9.0 0.055 8-12 Severe, concentrated defects
7.5 0.045 5-8 Moderate defects
6.5 0.038 2-4 Minor, scattered defects

The relationship can be conceptually expressed as the propensity for oxide formation:
$$ P_{slag} \propto [Mg]_{res}^{n} $$
where $P_{slag}$ is the probability or severity of slag inclusion defect formation, $[Mg]_{res}$ is the residual magnesium content, and $n > 0$. This confirmed that minimizing the Mg addition was crucial for controlling the slag inclusion defect.

2. Influence of Metal Pouring Temperature

Temperature critically affects metal viscosity and oxidation kinetics. Lower temperatures increase viscosity, impeding the floatation and removal of primary slag particles formed during treatment. More importantly, it promotes the formation of a secondary oxidation dross on the metal surface in the mold. Based on process data and observations, the effect can be summarized as follows:

  • $T_{pour} > 1320°C$: Minimal slag inclusion defects. High fluidity allows for good slag separation.
  • $1300°C < T_{pour} < 1320°C$: Thin oxide films begin to form on the metal meniscus.
  • $T_{pour} < 1280°C$: Severe formation of solid oxide particles and crusts, leading to definite slag inclusion defect entrainment.

The formation of MgO, a primary component of the slag, is highly temperature-dependent:
$$ 2Mg_{(in Fe)} + O_2 \rightarrow 2MgO_{(s)} \quad \Delta G = \Delta G^\circ + RT \ln\left(\frac{1}{a_{Mg}^2 \cdot p_{O_2}}\right) $$
While the free energy $ \Delta G $ for this reaction is negative at casting temperatures, a lower $T$ reduces atomic diffusion, causing formed oxides to remain dispersed as solid particles rather than coalescing into a removable surface layer. Higher temperature is therefore essential to manage slag inclusion defect.

3. Influence of Mold Conditions

A significant source of slag was identified as secondary oxidation within the mold cavity due to turbulent metal flow caused by mold gas evolution (venting). This was particularly observed near heavy sections and chills. Initial suspicion fell on rusted chills decomposing to release oxygen: $2FeO \rightarrow 2Fe + O_2$. However, dedicated experiments with rusted/un-rusted and coated/uncoated chills proved this was not the primary cause under the given conditions, as the local temperature was insufficient for rapid decomposition.

The real issue was inadequate venting of core assemblies. When metal rapidly surrounded a core, the trapped moisture and gases were forced through the molten metal, causing localized boiling (“metal eruption”) and severe oxidation. The problem was solved by ensuring superior core venting, particularly from the highest points of core assemblies. The relationship between sand moisture, gas pressure, and defect formation is key:
$$ P_{gas} = \frac{n_{H_2O} \cdot R \cdot T}{V_{core}} $$
Where $P_{gas}$ is the gas pressure built up inside the core, $n_{H_2O}$ is the moles of water vaporized, $R$ is the gas constant, $T$ is the local temperature, and $V_{core}$ is the core cavity volume. If $P_{gas}$ exceeds the local metallostatic pressure $(\rho g h)$, gas blows through the metal, creating turbulence and oxide films that lead to a slag inclusion defect.

4. Influence of Gating System Design

The original gating system was a partially unpressurized design with multiple ingates. Analysis of defect locations, especially on the 5th main bearing journal, revealed a critical flaw. A shared vent/riser at the flange end created a cross-connection between the two cavities in a mold. If filling was unbalanced, cooler, slag-laden metal from one cavity could backflow into the other, directly causing a slag inclusion defect at the flange and adjacent journal.

The solution was a comprehensive redesign:

  1. Adoption of a fully pressurized gating system to ensure calm, non-turbulent filling. The recommended area ratios became: $A_{sprue} : A_{runner} : A_{ingate} = 1.0 : 1.2 : 1.4$.
  2. Relocation and consolidation of ingates to direct metal flow more smoothly and minimize oxidation.
  3. Elimination of the shared vent that caused cross-flow. Individual, adequately sized vents were provided for each casting.

The effectiveness of gating is often assessed via the velocity head; minimizing velocity reduces turbulence and air entrainment:
$$ h = \frac{v^2}{2g} $$
where $h$ is the velocity head, $v$ is the metal velocity at the ingate, and $g$ is gravity. A pressurized system maintains a full runner, reducing $v$ and thus $h$, which is critical for preventing the slag inclusion defect.

III. Implemented Preventative Measures and Results

Based on the above analysis, the following integrated measures were implemented to combat the slag inclusion defect:

Table 3: Summary of Key Countermeasures Against Slag Inclusions
Factor Original Parameter Optimized Parameter Rationale
Mg Addition Nodularizer: ~9% Mg
Residual Mg: 0.05-0.06%
Nodularizer: 6-7% Mg
Residual Mg: ≤0.04%
Residual RE: ≤0.03%
Minimize source of reactive elements that form dross.
Pouring Temp. 1280-1320°C >1320°C (Strict minimum) Enhance fluidity for slag floatation; reduce surface oxide film formation.
Slag Treatment Cryolite powder added post-treatment. Block cryolite added post-treatment + powder cover before pouring. Improve agglomeration and removal of primary slag; protect metal surface from air.
Mold/Core Venting Standard venting, occasional core blows. Enhanced, dedicated venting from all core high points. Prevent gas-induced turbulence and metal oxidation inside the cavity.
Gating System Partially pressurized, multiple ingates, shared vent. Fully pressurized ($\Sigma A_{ingate} < \Sigma A_{runner}$), streamlined flow, isolated vents. Ensure quiescent, non-turbulent mold filling to avoid dross entrainment.

The quantitative outcome of these changes was significant. For the initial crankshaft model, the magnetic particle inspection (MPI) qualification rate rose from below 90% to over 98%, stabilizing the overall scrap rate for slag inclusion defect and other related issues to below 3%.

For a larger, heavier crankshaft produced via a horizontal pour-vertical cooling process, the risk was even greater due to longer cooling times and increased oxidation exposure. The optimized practice, particularly the strict control of Mg, high pouring temperature, and the use of block cryolite for slag washing, proved equally effective. The MPI qualification rate for this larger component stabilized above 96%.

IV. Generalized Principles for Slag Inclusion Prevention in Heavy NCI Castings

The investigation leads to several fundamental principles for minimizing slag inclusion defect in nodular iron:

  1. Minimize Reactive Elements: Use the lowest possible residual Mg and RE levels that guarantee the required nodularity. This directly reduces the “fuel” for dross formation. The target should satisfy the nodularizing threshold with a safety margin: $[Mg]_{res(min)} = k \cdot [S]_{initial}$, where $k$ is a process-dependent factor, but should be kept as low as possible.
  2. Maximize Temperature: Pour at the highest feasible temperature to lower viscosity and promote slag coalescence and floatation. The temperature must be balanced against shrinkage concerns, but for heavy-section castings prone to slag, the priority should be on temperature.
  3. Engineer Calm Filling: Employ a pressurized, streamlined gating system that introduces metal at the lowest point of the cavity with minimal turbulence. The ingate velocity should be controlled to prevent air entrainment.
  4. Ensure Mold Inertness: Guarantee excellent mold and core dryness (low moisture content) and provide abundant, direct venting paths to prevent gas-driven re-oxidation of the flowing metal.
  5. Implement Active Slag Management: Use effective slag-conditioning agents (like cryolite) both during ladle treatment to coagulate primary slag and as a protective cover before pouring to shield against atmospheric oxidation. The total dross content $C_{dross}$ can be conceptually modeled as:
    $$ C_{dross} = C_{primary}([Mg], [S], T_{tap}) + C_{secondary}(T_{pour}, t_{exposure}, v_{metal}, [O]_mold) $$
    The process goal is to minimize both terms through the described controls.

By systematically addressing each stage of the process—from alloy selection and treatment to mold design and pouring—the pervasive and costly problem of slag inclusion defect in large nodular iron castings can be brought under effective control, leading to dramatic improvements in yield and product quality.

Scroll to Top