In the continuous pursuit of efficiency and sustainability within the iron and steel industry, the longevity of blast furnaces stands as a critical factor, particularly under the imperative of green and low-carbon ironmaking. The service life of cooling staves is undoubtedly one of the most pivotal elements influencing the campaign life of a blast furnace. As essential water-cooled components forming the furnace lining, these staves endure severe operational conditions including scouring by gas flows, abrasion from burden materials, and erosion by high-temperature molten slag and iron. Consequently, they must possess excellent comprehensive properties such as thermal strength and resistance to thermal shock, which are fundamentally determined by the choice of material, structural design, and manufacturing processes. The primary materials for stave bodies include gray cast iron, ductile cast iron, heat-resistant cast iron, and steel castings, all belonging to the ferrous category. With the intensification of smelting operations, the zone of maximum thermal load has gradually shifted downward to the lower shaft, belly, and bosh regions, imposing even higher demands on the quality of staves in these critical areas. This investigation focuses on the post-campaign analysis of both cast iron and steel castings cooling staves from a commercial blast furnace, providing a comparative study of their damage behavior to inform better selection and design for prolonged service life.
1. Research Methodology and Stave Sampling
Following the final campaign of the blast furnace, which lasted approximately nine years with a cumulative hot metal output exceeding 11 million tons, a comprehensive investigation was initiated. Stave samples were retrieved from the high thermal load region, specifically the lower shaft area. This included sections from the 9th segment, constructed from steel castings, and the 11th segment, constructed from ductile cast iron. The methodology encompassed a systematic approach to evaluate their post-service condition.
The investigation proceeded through several key stages: macroscopic observation of the hot-face to document wear patterns and brick loss; detailed measurement of the dovetail fin wear rates; and a full anatomical dissection of the stave bodies. The dissection was performed using a large planer-milling machine, allowing for sequential layer-by-layer removal of material from the hot face (0 mm) towards the cold face, stopping at the plane containing the cooling pipe centerlines (95 mm for the steel castings, 70 mm for the cast iron). During this process, cuttings were collected at various depths and horizontal positions (upper, middle, lower sections) for subsequent chemical analysis. Samples of scale deposited inside the cooling water pipes were also extracted for compositional study. Furthermore, standard tensile test specimens and metallographic samples were prepared from both the hot-face and cold-face regions of the dissected blocks to assess the degradation in mechanical properties and microstructural evolution.
2. Macroscopic Damage and Wear Analysis
Initial visual inspection of the stave hot faces after cleaning revealed that while both stave bodies remained largely intact without pipe exposure, significant wear was evident. The refractory bricks inserted into the dovetail grooves had completely脱落ed. The residual dovetail fins on both staves exhibited a serrated appearance. The cast iron stave displayed more severe hot-face wear, with nearly one-third of the fins worn down to their roots. The primary mechanisms for this morphology are attributed to the combined effects of abrasive wear from descending burden and erosive wear from ascending gas flows within the furnace shaft.
To quantify the wear, the volume loss of each individual dovetail fin was measured. The wear rate $W_r$ for a fin is defined as:
$$W_r = \frac{V_{lost}}{V_{original}} \times 100\%$$
where $V_{lost}$ is the volume of material worn away, measured by filling the missing section with a material of known density, and $V_{original}$ is the fin’s as-designed volume. The results, presented in the table below, show a clear distinction between the two materials.
| Stave Type & Segment | Average Fin Wear Rate (%) | Wear Rate Range (%) | Overall Condition |
|---|---|---|---|
| Steel Castings (Segment 9) | 46.56 | 33.84 – 64.06 | Moderate wear, decreasing from top to bottom fins. |
| Ductile Cast Iron (Segment 11) | 73.3 | 57.18 – 100 | Severe wear, particularly at the top and bottom fins. |
The data indicates that despite operating in a potentially harsher environment lower in the shaft, the steel castings stave demonstrated superior resistance to volume loss, with an average wear rate significantly lower than its cast iron counterpart. The localized severe wear at the extremities of the cast iron stave suggests vulnerability to specific flow dynamics or thermal gradients.
3. Anatomical Dissection and Internal Damage
The layer-by-layer dissection provided critical insights into the internal damage state invisible from the surface, revealing profound differences between the two material types.
3.1 Crack Propagation and Network
The internal crack networks were markedly different. In the steel castings stave, cracks initiating from the hot face propagated inwards but terminated at a depth of approximately 60 mm, well before reaching the cooling pipes. These were primarily longitudinal cracks associated with the dovetail fins.
In stark contrast, the cast iron stave exhibited a much more extensive and severe crack network. Both longitudinal and transverse cracks were observed from the hot face. Critically, multiple cracks propagated completely through the stave body thickness, reaching the vicinity of and extending over the cooling pipes. Several transverse cracks were found to span the entire width of the stave block. This pervasive cracking, likely initiated and propagated by thermal shock (thermomechanical fatigue) during operational thermal cycles, severely compromises the structural integrity of cast iron staves and can lead to catastrophic spalling of large sections, ultimately exposing the cooling pipes.
3.2 Chemical Composition Gradients
Chemical analysis of cuttings taken from different depths revealed elemental migration due to long-term exposure to high temperatures and gaseous environments. The results are summarized below:
| Material | Key Observation | Probable Mechanism | Implication |
|---|---|---|---|
| Steel Castings | Decreasing C content from cold face to hot face. Si, P, S stable. Mn content increased towards hot face. | Decarburization and oxidation of carbon at the hot face. Possible inward diffusion/migration of Mn. | Surface layer softening, reduction in strength and hardness, degrading wear resistance. |
| Ductile Cast Iron | Decreasing C and Si content from cold face to hot face. Mn, P, S relatively stable. | Decarburization and oxidation of C and Si at the hot face. | Significant degradation of matrix structure near hot face, promoting graphitization and loss of mechanical properties. |
The decarburization process can be conceptually linked to a diffusion-controlled reaction, where carbon atoms migrate from regions of high concentration (the bulk) to the surface where they react with oxidizing species. The rate can be influenced by temperature and time, following principles akin to Fick’s laws.
3.3 Cooling Pipe Interface and Scaling
A critical finding was the condition of the cooling pipe-to-stave body interface. In the steel castings stave, the pipe was found to be in intimate metallic contact with the surrounding stave body, with no detectable gap. This ensures optimal heat transfer from the stave body into the cooling water. Conversely, in the cast iron stave, a clear, visible gap existed at the interface, with a maximum measured width of 0.92 mm. This gap creates a significant thermal resistance, drastically reducing the effective heat transfer coefficient and leading to higher operating temperatures in the stave body, which exacerbates thermal stress and accelerates damage.
The heat flux $q$ through the stave can be severely impeded by such a gap. The thermal resistance $R_{gap}$ of an air gap is given by:
$$R_{gap} = \frac{L_{gap}}{k_{air}}$$
where $L_{gap}$ is the gap thickness and $k_{air}$ is the thermal conductivity of air (a poor conductor). This resistance is in series with other resistances, causing a substantial temperature drop $\Delta T_{gap}$ across it: $\Delta T_{gap} = q \cdot R_{gap}$.
Furthermore, both types of staves had significant scale deposition inside the cooling water pipes. The scale was reddish-brown, flaky, and loosely adherent. Chemical and XRD analysis confirmed it was primarily iron oxide ($Fe_3O_4$), not calcium or magnesium salts. This indicates an electrochemical corrosion mechanism where the steel pipe material oxidizes in contact with the cooling water. The formation of scale, even a thin layer, drastically reduces heat transfer efficiency. A 1 mm scale layer can reduce heat removal capacity by over 80%, forcing the stave hot face to operate at dangerously elevated temperatures.

The manufacturing process for high-integrity steel castings, such as those required for cooling staves, involves precise mold design, controlled pouring, and sophisticated heat treatment to achieve the necessary microstructure, dimensional accuracy, and bonding with embedded cooling pipes—factors all critical to their superior in-service performance highlighted in this study.
4. Evolution of Material Properties and Microstructure
4.1 Mechanical Properties Degradation
Tensile tests on specimens machined from the cold and hot face regions revealed the extent of property loss. The results are consolidated below:
| Property & Location | Steel Castings Stave | Ductile Cast Iron Stave | As-New Standard |
|---|---|---|---|
| Tensile Strength (Cold Face) | ~460 MPa | ~350 MPa | 450-500 MPa (Steel); >400 MPa (D.I.) |
| Tensile Strength (Hot Face) | ~360 MPa | ~310 MPa | As above |
| Fracture Behavior | Cold face: Some plastic deformation. Hot face: Brittle fracture after peak load. | Brittle fracture at peak load for both faces. | Ductile behavior for steel; brittle for cast iron. |
The steel castings retained relatively good strength at the cold face, close to its original specification. The hot face showed a measurable drop, falling below the standard range. The cast iron stave exhibited degraded strength at both faces, failing to meet its expected strength grade. The stress-strain curves confirmed a complete loss of ductility in the cast iron and a transition to brittle behavior in the hot-face region of the steel. This degradation is attributed to microstructural changes, decarburization, and creep phenomena at sustained high temperatures. The creep strain rate $\dot{\epsilon}_c$ often follows a power-law relationship with stress $\sigma$:
$$\dot{\epsilon}_c = A \sigma^n \exp\left(-\frac{Q}{RT}\right)$$
where $A$ and $n$ are constants, $Q$ is the activation energy, $R$ is the gas constant, and $T$ is the absolute temperature. Operating temperatures, especially for the hot face, can be high enough to activate such creep mechanisms, leading to permanent deformation and microcracking under stress.
4.2 Microstructural Analysis
Metallographic examination provided the underlying reason for the mechanical property changes. The cold face of the cast iron stave showed a ferritic matrix with nodular (spheroidal) graphite, some of which was surrounded by ferrite forming a “bull’s-eye” structure. However, other graphite forms (flakes, vermicular) and cementite networks were also present. The hot face microstructure showed a reduction in perfect graphite nodules and an increase in degenerate graphite forms. The matrix also showed signs of degradation.
In contrast, the steel castings exhibited a more stable microstructure. The cold face consisted of ferrite and pearlite. The hot face, while potentially experiencing temperature fluctuations, showed a remarkably similar ferrite-pearlite structure. This indicates the superior thermal stability and resistance to microstructural degradation of the steel castings material under blast furnace conditions. Its higher thermal conductivity also helps maintain a more uniform temperature field, mitigating severe thermal gradients that drive damaging phase transformations.
5. Synthesis of Damage Mechanisms and Root Cause Analysis
The investigation points to a synergistic combination of mechanisms leading to stave deterioration, with significant differences in how the two materials respond.
Primary Damage Drivers:
- Abrasion & Erosion: Constant scouring by solid/coke particles and ascending gas flows causes progressive wear of the hot face and dovetail fins. The steel castings demonstrated inherently better wear resistance, as quantified by the lower fin wear rates.
- Thermal Shock (Thermal Fatigue): Rapid temperature fluctuations during furnace operations (e.g., burden slips, changes in gas flow) induce cyclic thermal stresses. The fundamental thermal stress $\sigma_{th}$ generated in a constrained body subjected to a temperature change $\Delta T$ is proportional to:
$$\sigma_{th} \propto E \cdot \alpha \cdot \Delta T$$
where $E$ is Young’s modulus and $\alpha$ is the coefficient of thermal expansion. The cast iron’s inferior thermal conductivity and the presence of the pipe gap lead to steeper thermal gradients ($\Delta T$), generating higher stresses. Furthermore, cast iron’s lower fracture toughness makes it more susceptible to crack initiation and propagation under these stresses, explaining the extensive internal crack network.
- Degradation of Heat Transfer: This is a critical accelerator. Two factors are at play:
- Pipe-Stave Gap (Cast Iron): This air gap acts as a major thermal barrier, reducing the cooling efficiency and causing the stave body to run hotter.
- Internal Pipe Scaling: The iron oxide scale insulates the cooling water from the pipe wall, reducing heat extraction. The combined effect forces the stave hot face to operate at elevated temperatures, accelerating all other degradation processes like decarburization, creep, and oxidation.
- Material Property Degradation: Long-term exposure to high temperatures leads to decarburization, graphitization (in cast iron), and microstructural changes that reduce strength, hardness, and toughness. This creates a vicious cycle: weaker material is more susceptible to wear and crack growth, which further compromises cooling and leads to even higher temperatures.
The superior performance of the steel castings stave can be attributed to its combination of properties: better high-temperature strength and microstructural stability, higher thermal conductivity leading to a more favorable temperature distribution, and the absence of a casting gap at the pipe interface ensuring efficient cooling. These factors collectively result in less severe wear, contained crack propagation, and retained mechanical integrity compared to the ductile cast iron stave.
6. Conclusions and Recommendations for Longevity
This detailed post-mortem analysis of blast furnace cooling staves after a full campaign leads to the following definitive conclusions and engineering recommendations:
Conclusions:
- The steel castings cooling stave exhibited significantly better overall performance than the ductile iron stave in the high thermal load zone. This was evidenced by a nearly 27% lower average dovetail fin wear rate, a contained internal crack network that did not reach the cooling pipes, and better retention of mechanical properties, particularly at the cold face.
- The most severe damage mechanism for the cast iron stave was the extensive network of transverse and longitudinal cracks, propagated by thermal shock, which severely threatened its structural integrity.
- A critical failure point unique to the cast iron stave was the presence of a substantial gap (up to 0.92 mm) at the cooling pipe-to-body interface. This defect, likely originating from the casting and solidification process, creates a catastrophic thermal barrier, fundamentally impairing the stave’s cooling function and accelerating all other damage mechanisms.
- Internal scaling, composed mainly of magnetite ($Fe_3O_4$), was found in both stave types, significantly impairing heat transfer. Water treatment and material selection for pipes must address this electrochemical corrosion.
- Chemical and microstructural degradation (decarburization, graphitization) at the hot face weakens the material, reducing its resistance to abrasion and crack growth. The steel castings material showed greater stability in this regard.
Recommendations for Enhanced Blast Furnace Longevity:
- Material Selection for High-Load Zones: For the lower shaft, belly, and bosh, steel castings should be strongly preferred over conventional ductile iron due to their superior combination of thermal conductivity, high-temperature strength, thermal fatigue resistance, and stability of the pipe-matrix bond.
- Manufacturing Quality Control: For any stave material, eliminating gaps at the cooling pipe interface is paramount. Manufacturing processes for steel castings must ensure perfect metallurgical bonding. Advanced casting techniques or forging/machining of pipe channels should be explored.
- Water Quality Management: Implementing effective water treatment regimens to minimize scaling is essential. This includes controlling oxygen content, pH, and using scale inhibitors to protect the internal pipe surfaces.
- Operational Stability: Smooth furnace operation minimizing large thermal fluctuations helps reduce thermal shock, a primary driver of cracking, especially in less resistant materials.
- Design Considerations: The geometry of dovetail fins and their connection to the stave body should be optimized to reduce stress concentrations. The superior toughness of steel castings allows for more robust designs in these critical areas.
In summary, the pursuit of blast furnace longevity is a multidisciplinary challenge. This investigation underscores that the choice of stave material—favoring high-performance steel castings for critical zones—coupled with impeccable manufacturing quality to ensure perfect cooling circuit integrity, and supported by prudent water treatment and operational practices, forms the cornerstone of a strategy to achieve extended, safe, and efficient furnace campaigns.
