On-Site Remediation of Casting Defects in Critical Mill Components: A First-Hand Account

The reliable operation of vertical roller mills (VRMs) is paramount in modern mineral processing and cement production. These complex machines integrate grinding, drying, classification, and material transport, offering significant advantages in efficiency, footprint, and environmental control. Their widespread adoption across industries like cement, power, and metallurgy has, however, brought maintenance challenges into sharper focus. Among these, addressing critical failures in large, integral cast components presents a unique set of difficulties. The constraints of the plant environment—limited space, lack of specialized machining tools, and the imperative for precision—often turn what would be a standard workshop repair into a complex field engineering project. This account details a comprehensive, field-executed repair strategy for a significant casting defect within a mill bearing housing, a procedure validated by a decade of subsequent successful operation.

The subject was a bearing housing on an LM-type vertical roller mill. During post-installation inspections, a significant casting defect was identified on the housing’s surface: clear, visible cracking indicative of either a shrinkage flaw or slag inclusion from the original casting process. Left unaddressed, such a defect could propagate under the mill’s cyclical and impact-heavy loading, leading to catastrophic failure. The decision was made to perform an on-site repair to restore structural integrity. The successful remediation followed a meticulous five-step procedure, which can be summarized as follows:

Step Core Action Primary Objective
1. Layout & Defect Removal Ultrasonic testing, marking, and controlled grinding. Complete physical removal of all defective material.
2. Preheating Uniform heating of the component to a specific temperature. Prevent weld cracking and reduce thermal stress.
3. Welding (Build-Up) Controlled deposition of weld metal using SMAW. Rebuild the material to its original dimensions and strength.
4. Finishing & Correction Precision grinding, polishing, and shape correction. Achieve final dimensional accuracy and surface finish.
5. Measurement & Verification Comprehensive dimensional checks. Confirm all specifications are within drawing tolerances.

Step 1: Layout and Complete Defect Excision

The initial and most critical phase is the absolute removal of all flawed material. The casting defect often runs deeper than surface cracks suggest. The process began with non-destructive testing (NDT). Ultrasonic testing was employed to map the subsurface extent of the flaw, providing a preliminary guide for the removal boundaries. Based on this map, the area was marked on the housing surface. To prevent any existing crack from propagating during the cutting process, “stop holes” were drilled at both extremities of the visible crack. The removal was executed not with a carbon arc gouge—which introduces carbon and can cause hardening—but with a controlled, handheld grinding wheel. The cutting strategy was deliberate: start grinding at a point approximately 10 mm above the suspected deepest point of the defect, angling the cut at about 30 degrees downwards to meet a horizontal line about 10 mm below the defect. This V-groove technique ensures complete access and visibility. After each grinding pass, liquid penetrant testing (dye check) was immediately performed on the newly exposed surface. If the test revealed any remaining indications of the casting defect, the grinding depth was incrementally increased until a completely sound metal base was achieved. This iterative process of grind-and-inspect is non-negotiable; welding over any remnant flaw will guarantee future failure.

Step 2: Controlled Preheating

The bearing housing was manufactured from a weldable cast steel, such as G20Mn5. Despite its good weldability, the large mass of the housing and the localized nature of the repair create a severe risk of hydrogen-induced cold cracking and excessive hardening in the Heat-Affected Zone (HAZ). Preheating is the essential countermeasure. It serves multiple purposes: it slows the cooling rate post-weld, allowing hydrogen to diffuse out; it reduces the hardness of the HAZ; and it minimizes thermal gradients and resultant stresses. The optimal preheat temperature (\(T_p\)) is a function of the material’s carbon equivalent (\(C_{eq}\)) and the section thickness. A commonly used formula for determination is:

First, calculate the base carbon equivalent using an adapted formula. For the likely steel composition, a standard IIW carbon equivalent formula is applicable:

$$[C]_{eq} = C + \frac{Mn}{6} + \frac{(Cr + Mo + V)}{5} + \frac{(Ni + Cu)}{15}$$

Given the approximate composition of G20Mn5, the carbon equivalent is moderate. To account for the restraining effect of the thick section, a thickness factor is incorporated. A practical method involves the following calculation for preheat temperature:

$$T_p (^{\circ}C) = 350 \times [C]_{eq} – 0.25$$

Based on the material specifications and a section thickness exceeding 100mm, the calculated and applied preheat temperature was maintained at approximately 150-200°C. Heating was achieved uniformly around the repair zone using electrical heating blankets or, where necessary, multiple rosebud torches, with temperature constantly monitored by infrared thermometers. Crucially, to minimize distortion during heating and subsequent welding, the housing was mechanically restrained by bolting on its mating covers and end plates.

Material (Typical) C Mn Si P Max S Max Approx. [C]eq
G20Mn5 Cast Steel 0.17-0.23% 1.00-1.60% 0.60% 0.020% 0.020% ~0.45%

Step 3: Precision Welding and Build-Up

With the component uniformly preheated and held at temperature, the welding process commenced. Shielded Metal Arc Welding (SMAW or “stick” welding) was selected for its versatility and controlled heat input in a field setting. The filler metal was a low-hydrogen electrode with mechanical properties matching the base material (e.g., a high-tensile strength, low-alloy type). Electrodes were properly baked according to manufacturer specifications to remove moisture, a critical source of hydrogen. The welding procedure was meticulously controlled:

  • Low Heat Input: Small diameter electrodes (2.5 mm for root passes, 3.2 mm for fill passes) were used with the lowest practical amperage to minimize dilution and heat concentration.
  • Layer-by-Layer Deposition: The cavity was filled using a horizontal stringer bead technique. Each bead was thoroughly cleaned of slag before the next was applied.
  • Peening: To relieve internal stresses, each weld layer was peened immediately while still warm (between 100-200°C) using a round-nose pneumatic tool or hand hammer. This mechanical working helps to counteract shrinkage stress.
  • Interpass Temperature Control: The temperature of the repair zone was monitored to ensure it never fell below the minimum preheat temperature, requiring intermittent reheating. Conversely, it was prevented from exceeding 300°C to avoid excessive heat buildup.

Upon completion of the weld build-up, the entire housing was covered with insulating blankets to facilitate a very slow, controlled cool-down to ambient temperature, a process that may take 24 hours or more. This post-weld slow cooling is as vital as preheating in preventing hard, crack-prone microstructures.

Step 4: Finishing, Polishing, and Dimensional Correction

Even with all precautions, some distortion is inevitable. The final internal bore dimensions and surface finish are critical for proper bearing fitting and operation. The challenge was to restore these in the field without a portable boring machine. The strategy combined skilled manual grinding with a thermal correction technique. First, the weld cap was ground down flush with the surrounding original surface using coarse grinding discs. As the final dimensions were approached, finer grinding and finally rotary polishing tools were used to achieve the required surface finish (Ra value).

To correct for distortion-induced out-of-roundness or taper, a “counter-distortion” method was employed. After allowing the housing to cool completely, its internal geometry was meticulously mapped using inside micrometers and dial gauges, referenced to a network of scribed longitudinal and circumferential lines. The pattern and magnitude of distortion were analyzed. By applying carefully localized heating (using a torch) to specific points on the housing’s external structure, controlled thermal expansion was induced to “push” the distorted bore back towards its true cylindrical form. This process, which requires significant experience and may be iterative, effectively uses heat as a precision adjustment tool. After each thermal adjustment, the housing was allowed to cool naturally, and measurements were retaken. This cycle was repeated until the bore dimensions were within the strict tolerances specified by the bearing manufacturer.

Step 5: Final Measurement and Verification

The success of the entire operation hinges on verification. A comprehensive final measurement protocol was executed. Using an array of precision tools—inside micrometers, telescopic gauges, and dial indicators—the bore’s diameter was measured at multiple axial planes (e.g., near the top, middle, and bottom) and at numerous radial clock positions (every 30 degrees). This data was used to calculate:

  • Roundness/Cylindricity: The deviation from a perfect circle at any given cross-section.
  • Taper: Any consistent change in diameter along the axis of the bore.
  • Surface Finish: Verified by comparison against finish samples.

All measured parameters were documented and confirmed to be within the original equipment drawing specifications. A final non-destructive test, typically a magnetic particle or liquid penetrant inspection of the entire repaired area and its periphery, was conducted to guarantee the weld integrity and confirm the complete eradication of the original casting defect and the absence of any new flaws introduced during repair.

Conclusion and Long-Term Perspective

The remediation of major casting defects in critical mill components on-site is a demanding but entirely feasible engineering undertaking. It demands a systematic, physics-based approach that respects the metallurgy of the base material. The five-step methodology—from the uncompromising removal of flawed material and controlled thermal management during welding to the skillful final machining and verification—forms a robust framework for such repairs. The core principles are universal: understand the material, control heat, relieve stress, and verify quality at every stage. This particular repair, executed over a decade ago, stands as testament to the longevity that such a careful field repair can achieve. It underscores that with proper methodology, even significant casting defects need not lead to prolonged downtime or the prohibitive cost of component replacement, thereby ensuring the continued reliability and productivity of vital industrial grinding equipment.

Scroll to Top