Effect of Antimony on Heavy Section Ductile Iron Casting

In the realm of advanced materials, ductile iron casting stands out due to its exceptional combination of mechanical properties, corrosion resistance, and machinability. Over the past decades, ductile iron casting has found widespread applications across various industries, from automotive components to heavy machinery. The performance of ductile iron casting can be tailored over a broad range—exhibiting high ductility, strength, and wear resistance—primarily dictated by its graphite morphology and matrix structure. This versatility makes ductile iron casting a material of choice for demanding applications. However, producing heavy section ductile iron casting, such as those with thicknesses exceeding 70 mm, presents significant challenges. These include issues like graphite degradation, matrix inhomogeneity, and reduced mechanical properties at the core due to slower cooling rates. To address these challenges, alloying elements and heat treatments are often employed to refine the microstructure and enhance performance.

Among various alloying elements, antimony (Sb) has garnered attention for its dual role in ductile iron casting. On one hand, Sb is known as a graphite spheroidizing干扰元素, potentially deteriorating graphite morphology if not controlled. On the other hand, when combined with rare earth (RE) elements, Sb can promote pearlite formation, thereby increasing strength and hardness in ductile iron casting. This study delves into the effects of微量 Sb on the microstructure and mechanical properties of heavy section ductile iron casting, aiming to achieve the stringent requirements of grade QT800-2 through optimized chemistry and heat treatment. The focus is on understanding how Sb influences graphite形态, matrix refinement, and overall performance in thick sections, which is critical for applications like industrial castings where durability and reliability are paramount.

The importance of ductile iron casting in modern engineering cannot be overstated. Its ability to be cast into complex shapes with excellent properties makes it indispensable. However, for heavy section ductile iron casting, maintaining consistent properties throughout the cross-section is a persistent hurdle. Factors such as cooling rate variations and segregation can lead to inhomogeneities. Alloying with elements like copper (Cu), tin (Sn), and antimony (Sb) offers a pathway to mitigate these issues. In particular, Sb has shown promise in refining pearlite and enhancing strength, but its interaction with other elements and processing parameters needs careful examination. This research explores these aspects through systematic experimentation, providing insights into the optimal use of Sb in ductile iron casting for heavy sections.

To set the stage, let’s review the fundamental aspects of ductile iron casting. Ductile iron, also known as nodular iron, derives its name from the spherical graphite nodules embedded in the matrix, which are achieved through magnesium treatment during melting. These nodules act as crack arresters, imparting ductility and toughness. The matrix can be ferritic, pearlitic, or a combination, depending on composition and heat treatment. For high-strength applications like QT800-2, a fully pearlitic matrix with fine interlamellar spacing is desired. Achieving this in heavy section ductile iron casting requires precise control over chemistry and cooling. Alloying elements such as Cu and Sn are commonly used to promote pearlite, but Sb offers additional refinement potential. However, excessive Sb can lead to carbide formation and graphite恶化, necessitating a balanced approach.

In this study, we investigate the role of Sb in heavy section ductile iron casting, focusing on microstructure-property relationships. We employ a comprehensive methodology involving melting, treatment, casting, and heat treatment, followed by detailed characterization. The goal is to establish guidelines for producing ductile iron casting that meets QT800-2 specifications in sections up to 70 mm thick. Through this work, we aim to contribute to the broader understanding of alloy design for ductile iron casting, enabling more reliable and efficient manufacturing processes.

Before delving into the experimental details, it’s worth noting that the ductile iron casting industry continuously seeks improvements in material performance. Research on elements like Sb is part of this endeavor, with potential implications for sectors such as energy, transportation, and construction. By optimizing ductile iron casting for heavy sections, we can expand its applicability to larger and more critical components, driving innovation and sustainability. This paper presents our findings in a structured manner, beginning with materials and methods, followed by results, discussion, and conclusions.

Materials and Methods

Our approach to studying ductile iron casting involved careful selection of raw materials, precise chemical composition control, and standardized processing techniques. We focused on producing heavy section ductile iron casting with varying Sb contents to assess its effects. All experiments were conducted in an industrial setting to ensure relevance to real-world applications.

The raw materials for ductile iron casting consisted of pig iron, scrap steel, and returns (recycled ductile iron). The chemical composition of these materials is summarized in Table 1. We used a blend of 45% pig iron, 40% returns, and 15% scrap steel to achieve a base iron with low impurity levels. Petroleum coke was added as a carbon raiser, and ferrosilicon (75% Si) was used for silicon adjustment. The target base composition for the ductile iron casting was set to ensure proper graphitization and matrix control.

Material C (wt%) Si (wt%) Mn (wt%) P (wt%) S (wt%) Ti (wt%)
Pig Iron 4.33 0.719 0.098 0.024 0.0150 0.022
Scrap Steel 0.16 0.201 0.238 0.027 0.0028 0.046
Returns 3.60 2.53 0.190 0.030 0.0070 0.023

The target chemical composition for the ductile iron casting was as follows: carbon (C) 3.45–3.55%, silicon (Si) 1.95–2.05%, manganese (Mn) 0.2–0.3%, sulfur (S) 0.006–0.012%, and magnesium (Mg) 0.04–0.05%. Alloying elements included copper (Cu) at 1.0%, tin (Sn) at 0.15%, and antimony (Sb) at varying levels: 0%, 0.015%, 0.025%, and 0.035%. These additions were made to investigate the synergistic effects on ductile iron casting properties. The composition ranges were chosen based on prior research to balance graphitization and matrix hardening.

Melting was carried out in a 3-ton medium-frequency induction furnace. The charge materials were added in batches, with carbon raiser introduced early to ensure good absorption. Ferrosilicon was added in the final batch to minimize oxidation. The alloying elements—Cu, Sn, and Sb—were added after base composition adjustment, at a temperature around 1500°C. The molten iron was then tapped at approximately 1500°C and subjected to treatment for ductile iron casting.

The treatment process for ductile iron casting involved two key steps: nodularizing and inoculating. We used a冲入法 (pouring method) for nodularization. A mixture of Si-Mg alloy (6.66% Mg, 44.80% Si) and yttrium-based heavy rare earth (RE) alloy (7.10% Mg, 3.68% RE, 43.04% Si) was placed at the bottom of the treatment ladle, compacted and covered with 0.8% Si-Ba inoculant (67.36% Si, 5.96% Ba, 1.03% Ca). Additionally, 0.2% small steel scraps were added on top to facilitate reaction. After treatment, slag was removed, and instantaneous inoculation with 0.15% 75% SiFe granules (0.3–0.7 mm size) was performed during casting. The pouring temperature was controlled at 1320°C to ensure fluidity and minimize defects in the ductile iron casting.

For casting, we used resin sand molds to produce test blocks. The design included a main block with attached standard test samples of 70 mm thickness, as illustrated in Figure 1. The gating system was top-poured to ensure feeding and soundness for the heavy section ductile iron casting. The 70 mm thick samples were used for mechanical testing and microstructural analysis, representing the core properties of thick sections.

Heat treatment is crucial for achieving the desired matrix in ductile iron casting. We applied a normalizing and tempering cycle: heating to 940°C for 3 hours, followed by air cooling at a rate of 10–15°C/min, and then tempering at 460°C for 4 hours. This regimen aims to produce a fine pearlitic matrix with enhanced strength and toughness in the ductile iron casting. Temperature monitoring was done using thermocouples to ensure consistency.

Characterization of the ductile iron casting involved multiple techniques. Chemical analysis was performed using a direct reading spectrometer. Hardness was measured on square test blocks with a portable Brinell hardness tester. Tensile tests were conducted on φ14 mm standard specimens machined from the 70 mm thick attached blocks, using an electro-hydraulic universal testing machine. Microstructural examination was carried out with an optical microscope, focusing on graphite morphology and matrix details. Throughout this study, we emphasized reproducibility and statistical relevance, with multiple samples for each condition.

Results and Analysis

The effects of antimony on ductile iron casting were evaluated through microstructural observations and mechanical testing. We present the findings in terms of graphite morphology, matrix structure, and mechanical properties, highlighting the role of Sb in heavy section ductile iron casting.

Graphite Morphology

Graphite morphology is a critical factor in ductile iron casting, influencing ductility and strength. In our study, we examined how Sb additions affect graphite nodule shape and distribution. Without Sb, the graphite nodules in ductile iron casting were irregular and fewer in number, as shown in Figure 2a. This is typical for heavy sections where cooling is slow, leading to graphite degeneration. With 0.015% Sb, the nodules became more spherical, but the count remained low (Figure 2b). At 0.025% Sb, we observed a significant improvement: nodules were rounder and more numerous, approximately doubling in count (Figure 2c). However, at 0.035% Sb, the graphite morphology deteriorated again, with irregular shapes and reduced sphericity (Figure 2d).

These changes can be attributed to the interaction between Sb and rare earth elements. Sb is known to interfere with graphite spheroidization in ductile iron casting, but RE additions can counteract this effect. In our ductile iron casting, the combination of 0.1% heavy RE and 0.025% Sb yielded optimal graphite morphology. The mechanism involves RE neutralizing the反球化 effect of Sb, promoting nucleation of graphite nodules. The relationship between graphite nodule count (N) and Sb content (C_Sb) can be approximated by: $$ N = N_0 + k_1 C_{RE} – k_2 C_{Sb}^2 $$ where N_0 is the base count, k_1 and k_2 are constants, and C_RE and C_Sb are concentrations of RE and Sb, respectively. This nonlinear behavior underscores the delicate balance needed in ductile iron casting.

The image above illustrates a typical microstructure of ductile iron casting, showcasing graphite nodules in a matrix. In our samples, the best results were achieved with moderate Sb, emphasizing the importance of composition control in ductile iron casting.

Matrix Structure

The matrix of ductile iron casting determines its mechanical properties. We investigated the impact of Sb on pearlite refinement in the as-cast and heat-treated conditions. Without Sb, the pearlite in ductile iron casting had a coarse lamellar spacing and inhomogeneous distribution (Figure 3a). Adding 0.015% Sb resulted in finer pearlite with better uniformity (Figure 3b). At 0.025% Sb, the pearlite became even finer, and the matrix appeared more homogeneous (Figure 3c). However, at 0.035% Sb, we observed partial resolution of pearlite lamellae and the formation of少量 carbides (Figure 3d), which could embrittle the ductile iron casting.

After heat treatment, the matrix of ductile iron casting transformed to a more refined state. The normalizing and tempering process enhanced pearlite fineness, as seen in Figure 5. For instance, with 0.025% Sb, the pearlite片间距 was significantly reduced, contributing to higher strength. The interlamellar spacing (λ) can be related to Sb content via: $$ \lambda = \lambda_0 – \alpha C_{Sb} $$ where λ_0 is the spacing without Sb, and α is a refinement coefficient. However, at high Sb levels, carbide precipitation may occur, described by: $$ \text{Carbide volume fraction} \propto C_{Sb} – C_{crit} $$ where C_crit is a threshold around 0.03% for our ductile iron casting.

This refinement effect is crucial for heavy section ductile iron casting, where slow cooling often leads to coarse structures. Sb accelerates pearlite formation by increasing undercooling and nucleation sites, thereby improving the matrix of ductile iron casting. The synergy with Cu and Sn further enhances this, as these elements also promote pearlite. The overall matrix hardness (H) can be modeled as: $$ H = H_0 + \beta (\text{Pearlite fraction}) + \gamma (\text{Carbide fraction}) $$ where H_0 is the base hardness, and β and γ are contribution factors. In our ductile iron casting, the optimal Sb content maximized pearlite refinement without excessive carbide formation.

Mechanical Properties

The mechanical properties of ductile iron casting are the ultimate measure of performance. We tested tensile strength, yield strength, elongation, and hardness for different Sb contents after heat treatment. The results are summarized in Table 2. As Sb increased from 0% to 0.035%, tensile strength rose from 609.5 MPa to 908.7 MPa, and yield strength from 450.5 MPa to 615.5 MPa. However, elongation dropped from 4.93% to 1.46%, indicating a trade-off between strength and ductility in ductile iron casting.

Sb Content (wt%) Tensile Strength (MPa) Yield Strength (MPa) Elongation (%) Hardness (HB)
0 609.5 450.5 4.93 217–245
0.015 840.3 586.1 3.52 255–285
0.025 896.1 613.6 2.72 270–300
0.035 908.7 615.5 1.46 285–320

The improvements in strength are directly linked to matrix refinement in ductile iron casting. The Hall-Petch relationship can be adapted for pearlitic ductile iron casting: $$ \sigma_y = \sigma_0 + k_y \lambda^{-1/2} $$ where σ_y is yield strength, σ_0 is friction stress, k_y is a constant, and λ is interlamellar spacing. Sb reduces λ, thereby increasing σ_y. However, the decline in elongation is attributed to graphite morphology deterioration and carbide formation at high Sb levels. For heavy section ductile iron casting targeting QT800-2, a balance is needed: our data shows that 0.025% Sb yields tensile strength above 800 MPa and elongation around 2.7%, meeting the grade requirements.

Hardness values correlated with strength trends, increasing from about 230 HB to over 300 HB with Sb additions. This is consistent with the matrix hardening in ductile iron casting. The relationship between hardness (H) and tensile strength (σ_u) can be expressed as: $$ \sigma_u \approx 3.2 \times H \text{ (for ductile iron casting)} $$ This empirical formula held well in our study, validating the measurements.

Overall, the ductile iron casting with 0.025% Sb, along with 1.0% Cu and 0.15% Sn, achieved the desired properties after heat treatment. This composition ensures fine pearlite and good graphite morphology, enabling heavy section ductile iron casting to perform reliably in demanding applications.

Discussion

The findings from this study on ductile iron casting have several implications. First, the role of Sb in heavy section ductile iron casting is nuanced. While Sb refines pearlite and boosts strength, its interaction with RE is critical to maintain graphite quality. In industrial ductile iron casting production, this means that RE-containing nodularizers should be used when adding Sb to counteract its adverse effects. The optimal window for Sb in ductile iron casting appears to be around 0.02–0.03%, depending on other alloying elements and section size.

Second, the heat treatment regimen plays a vital role in ductile iron casting. Normalizing at 940°C allows austenitization and homogenization, while air cooling at controlled rates promotes fine pearlite in heavy section ductile iron casting. Tempering at 460°C relieves stresses and enhances toughness. This process is effective for achieving QT800-2 properties in ductile iron casting, as demonstrated by our results. However, variations in cooling rate due to section thickness must be accounted for; our use of attached test blocks simulated realistic conditions for ductile iron casting.

Third, the synergy between alloying elements in ductile iron casting cannot be overlooked. Cu and Sn promote pearlite but can also increase hardness. Sb adds an extra refinement dimension. The combined effect can be modeled using mixture rules: $$ P_{\text{effective}} = w_{Cu} P_{Cu} + w_{Sn} P_{Sn} + w_{Sb} P_{Sb} $$ where P represents pearlite-promoting potency, and w are weight fractions. For ductile iron casting, this helps in designing compositions for target microstructures.

Moreover, the economic aspects of ductile iron casting are important. Sb is a relatively low-cost addition compared to other alloys, making it attractive for enhancing ductile iron casting properties. However, careful control is needed to avoid scrap due to carbide formation. In production environments for ductile iron casting, real-time monitoring and process optimization can ensure consistency.

From a broader perspective, this research on ductile iron casting contributes to the advancement of material science. Heavy section ductile iron casting is used in wind turbines, pump housings, and大型 machinery, where performance dictates longevity. By improving the understanding of Sb effects, we enable better design and manufacturing of ductile iron casting components. Future work could explore dynamic loading or corrosion behavior of Sb-modified ductile iron casting.

Conclusions

In conclusion, this study on ductile iron casting reveals that antimony (Sb) significantly influences the microstructure and mechanical properties of heavy section ductile iron casting. Key findings include:

1. Graphite morphology in ductile iron casting is improved with moderate Sb additions (0.025%) when combined with rare earth elements, leading to more spherical nodules and higher counts. However, excess Sb (0.035%) deteriorates graphite, highlighting the need for balanced composition in ductile iron casting.

2. Sb strongly refines the pearlitic matrix in ductile iron casting, reducing interlamellar spacing and enhancing strength. But at high levels, it can induce carbide formation, which may compromise ductility. The refinement follows a linear trend up to a threshold.

3. Mechanical properties of ductile iron casting, such as tensile and yield strength, increase with Sb content, while elongation decreases. For heavy section ductile iron casting targeting QT800-2, an optimal composition of 1.0% Cu, 0.15% Sn, and 0.025% Sb, followed by heat treatment (940°C for 3 h + 460°C for 4 h), achieves the required performance: tensile strength over 800 MPa, yield strength around 615 MPa, and elongation above 2.5%.

These insights provide practical guidance for producing high-quality ductile iron casting for thick sections. By leveraging Sb’s benefits while mitigating its drawbacks through RE addition and controlled heat treatment, manufacturers can reliably meet stringent standards. Ductile iron casting continues to evolve, and such research paves the way for more robust and versatile applications.

Ultimately, the success of ductile iron casting depends on a holistic approach—integrating material design, processing, and quality control. As industries demand higher performance from cast components, ongoing innovation in ductile iron casting will remain essential. We hope this work stimulates further exploration into alloying strategies for ductile iron casting, driving progress in the field.

Scroll to Top