Local Squeeze Assisted HPDC for Reducing Casting Defects

Research objective. I investigated a high-pressure die casting (HPDC) process for an engine bracket in which a persistent casting defect reduced product quality and production efficiency. The casting defect appeared mainly as gas porosity and shrinkage porosity around a remote bearing hole. I combined theoretical analysis, CAE simulation, Taguchi process optimization, and a local squeeze process to reduce the casting defect. I treated the casting defect as a system-level problem rather than a single process-variable problem, because the defect was controlled by filling behavior, solidification behavior, local pressure transfer, and local mold structure at the same time.

Motivation. Lightweight automotive components require thin walls, complex ribs, and locally thick sections. These features increase the risk of casting defect formation in HPDC. For the engine bracket studied here, the maximum wall thickness was about 17 mm, the minimum wall thickness was about 3 mm, and the parting surface was not flat. The remote bearing hole was located above the main parting plane, so effective venting was difficult. As a result, gas was trapped near the last-filled region, and the intensification pressure could not act effectively on that region. The casting defect was therefore not eliminated by ordinary mold design changes or by normal process-window adjustment alone.

Approach. I first analyzed the formation mechanisms of gas porosity and shrinkage porosity in HPDC. I then built a CAE model to predict the casting defect location and to compare the prediction with production trials. After that, I used an L9 orthogonal array to evaluate the influence of high-speed velocity, high-speed interval, and intensification pressure on the casting defect. Because process optimization reduced but did not eliminate the casting defect, I designed a local squeeze unit and integrated it into the HPDC mold. The local squeeze unit applied pressure directly to the semisolid metal near the remote bearing hole, compressed the gas pores, and improved local density. I verified the result by X-ray inspection and sectioning. The final casting defect level was reduced to an acceptable range, with a maximum pore diameter of about 0.46 mm and a local porosity of about 0.6%.

HPDC fundamentals. In HPDC, molten metal is transferred into a shot sleeve, driven by a plunger at low speed, accelerated at high speed near the gate, and then intensified under high pressure during solidification. The casting defect formation is strongly related to the interaction between metal flow, air entrapment, heat transfer, and pressure transmission. I considered the classical flow descriptions used in die casting: the jet-flow concept, the sequential-filling concept, and the continuity concept. In practical HPDC, the filling pattern is not purely one-dimensional; it is a coupled thermal-fluid problem. The local casting defect near the remote hole was caused by a combination of air entrapment during filling and insufficient feeding during solidification.

Governing equations for filling. I treated the liquid metal as an incompressible Newtonian fluid during the filling stage. The mass conservation equation is:

$$ \frac{\partial u}{\partial x}+\frac{\partial v}{\partial y}+\frac{\partial w}{\partial z}=0 $$

The momentum conservation equations in three directions are:

$$ \rho\left(\frac{\partial u}{\partial t}+u\frac{\partial u}{\partial x}+v\frac{\partial u}{\partial y}+w\frac{\partial u}{\partial z}\right)= -\frac{\partial p}{\partial x}+\mu\nabla^2 u+\rho g_x $$

$$ \rho\left(\frac{\partial v}{\partial t}+u\frac{\partial v}{\partial x}+v\frac{\partial v}{\partial y}+w\frac{\partial v}{\partial z}\right)= -\frac{\partial p}{\partial y}+\mu\nabla^2 v+\rho g_y $$

$$ \rho\left(\frac{\partial w}{\partial t}+u\frac{\partial w}{\partial x}+v\frac{\partial w}{\partial y}+w\frac{\partial w}{\partial z}\right)= -\frac{\partial p}{\partial z}+\mu\nabla^2 w+\rho g_z $$

The energy conservation equation is:

$$ \rho c\left(\frac{\partial T}{\partial t}+u\frac{\partial T}{\partial x}+v\frac{\partial T}{\partial y}+w\frac{\partial T}{\partial z}\right)= k\nabla^2 T+S $$

The volume-of-fluid function for the free surface is:

$$ \frac{\partial F}{\partial t}+u\frac{\partial F}{\partial x}+v\frac{\partial F}{\partial y}+w\frac{\partial F}{\partial z}=0 $$

Where \(F=1\) means a fully filled cell, \(0<f<1\) \(f="0\)" a="" an="" and="" by="" cae="" casting="" cell,="" cell.="" defect.

Governing equations for solidification. During solidification, heat transfer is dominated by conduction, convection, and radiation. The Fourier heat conduction relation is:

$$ q=-k\frac{\partial T}{\partial n} $$

The transient heat conduction equation with latent heat release is:

$$ \rho c_p \frac{\partial T}{\partial t}= \lambda\left(\frac{\partial^2 T}{\partial x^2}+\frac{\partial^2 T}{\partial y^2}+\frac{\partial^2 T}{\partial z^2}\right)+\rho L \frac{\partial f_s}{\partial t} $$

Convective heat transfer follows Newton’s law:

$$ q=\alpha(T_w-T_f) $$

Radiative heat transfer follows the Stefan–Boltzmann law:

$$ q=\epsilon\sigma_0 T_s^4 $$

The general transport equation used in the simulation can be written as:

$$ \frac{\partial(\rho\phi)}{\partial t}+\nabla\cdot(\rho\mathbf{u}\phi)=\nabla\cdot(\Gamma\nabla\phi)+S_\phi $$

Here \(\phi\) is the transported variable, \(\Gamma\) is the diffusion coefficient, and \(S_\phi\) is the source term. I used these relations as the theoretical basis for interpreting the CAE results and for selecting the local squeeze timing.

Casting defect classification. I classified the relevant casting defect types into gas porosity, shrinkage porosity, and mixed porosity. Gas porosity usually has a smooth internal surface and is caused by trapped air or hydrogen. Shrinkage porosity usually has a rough internal surface and is caused by insufficient feeding during solidification. The remote bearing hole showed a mixed casting defect: gas was trapped because venting was poor, and the local thick section could not be fed effectively after the gate solidified. The following image illustrates typical casting defect morphology in aluminum castings.

Gas porosity mechanism. Gas porosity forms when air or gas cannot escape from the mold cavity before the metal solidifies. In HPDC, the metal front can entrap air when the filling pattern is turbulent. If the local mold cavity has a high parting step, a deep pocket, or no vent, the trapped air remains in the last-filled region. The intensification pressure can compress the gas to some extent, but if the local region has already formed a solid shell, the pressure cannot fully collapse the pore. This was the main mechanism of the casting defect near the remote bearing hole.

Shrinkage porosity mechanism. Shrinkage porosity forms when volume contraction during cooling cannot be compensated by liquid metal feeding. Thick sections cool more slowly than thin sections. The thermal gradient produces isolated liquid pools. If the gate or runner solidifies early, the pressure path is interrupted, and the isolated pool forms shrinkage pores. The remote bearing hole had a locally thick section, and the gate solidified after about 3 s, so later solidification could not be fed. Thus, the casting defect in this position had both gas and shrinkage contributions.

Defect acceptance criteria. I used the ASTM E505 reference for aluminum die castings as a qualitative acceptance guide. The acceptance level depends on wall thickness, pore diameter, and spacing between pores. The relevant criteria are summarized in Table 1. A casting defect with a maximum pore diameter above 1.2 mm was not acceptable for the critical region.

Wall thickness range Acceptance level Maximum single pore diameter Spacing requirement
3.2–9.5 mm Level 1 1.2 mm Pores of 0.5–1.2 mm must be at least 2.5 mm apart
3.2–9.5 mm Level 2 1.3 mm Pores of 1.0–1.3 mm must be at least 2.0 mm apart
3.2–9.5 mm Level 3 1.6 mm Pores of 1.0–1.6 mm must be at least 2.0 mm apart
9.5–25.4 mm Level 1 3.4 mm length Shrinkage length limit
9.5–25.4 mm Level 2 5.1 mm length Shrinkage length limit

Process parameters. I identified intensification pressure, high-speed velocity, high-speed interval, slow-shot velocity, pouring temperature, and mold temperature as the main variables influencing the casting defect. The pressure-related equations are:

$$ P_{\text{injection}}=\frac{\pi P_{\text{cylinder}}D_{\text{cylinder}}^2}{4} $$

$$ P_{\text{intensification}}=\frac{P_{\text{injection}}}{S_{\text{chamber}}} $$

The gate velocity is related to plunger velocity by continuity:

$$ v_{\text{gate}}=\frac{S_{\text{chamber}}v_{\text{plunger}}}{S_{\text{gate}}} $$

The high-speed interval was estimated from the metal volume and shot sleeve area:

$$ H_{\text{high}}=\frac{G_{\text{casting}}+G_{\text{overflow}}}{\rho S_{\text{chamber}}}+10 $$

For the engine bracket, the casting plus overflow mass was about 2.7223 kg, the shot sleeve area was about 50.3 cm², and the liquid aluminum density was about 2.6 g/cm³. The calculated high-speed interval was about 218 mm, so I selected about 220 mm for the initial simulation. The process parameters and their expected effects on the casting defect are summarized in Table 2.

Parameter Role in HPDC Effect on casting defect Typical range
Slow-shot velocity Stable metal transport in shot sleeve Too high causes air entrapment; too low causes cold metal 0.2–0.5 m/s
High-speed velocity Fast cavity filling Too high causes turbulence and gas porosity; too low causes cold shut 3.0–4.0 m/s
High-speed interval Switch point from slow to fast shot Wrong switch point increases air entrapment or incomplete filling 190–220 mm
Intensification pressure Compresses gas and feeds shrinkage Higher pressure reduces pore size but increases mold load 80–100 MPa
Pouring temperature Controls fluidity and solidification Too high increases shrinkage; too low reduces fillability 640–680 °C
Mold temperature Controls local cooling rate Nonuniform temperature promotes local casting defect 180–240 °C

Recommended intensification pressure. I used the standard recommendation for aluminum HPDC to set the initial pressure window. High-integrity and pressure-tight castings usually require higher intensification pressure. The recommended values are listed in Table 3. Because the engine bracket had a pressure-tightness requirement, I selected 80–100 MPa as the experimental range.

Casting type Aluminum alloy pressure Zinc alloy pressure Brass pressure
Light load, low strength 30–40 MPa 13–20 MPa 30–40 MPa
Heavy load, high strength 40–80 MPa 20–30 MPa 40–60 MPa
High gas tightness 80–120 MPa 25–40 MPa 80–100 MPa

Material properties. I used AlSi9Cu3 for the casting and H13 tool steel for the mold. The thermophysical properties used in the CAE model are given in Table 4 and Table 5. The pouring temperature was set to 650 °C, and the initial mold temperature was set to 180–220 °C depending on the trial. The interface heat transfer coefficient between the casting and the mold was described by a temperature-dependent function, while the mold-to-mold heat transfer coefficient was set to 3500 W/(m²·K) and the mold-to-cooling-channel coefficient was set to 2000 W/(m²·K).

Temperature / °C Thermal conductivity / W·m⁻¹·K⁻¹ Specific heat / J·kg⁻¹·K⁻¹ Density / kg·m⁻³
1 140.0 820 2650
50 142.5 860 2643
100 144.5 900 2637
200 147.5 950 2619
300 152.5 980 2597
400 148.0 1050 2575
479 141.5 1150 2555
578 70.0 1000 2530
2000 70.0 1000 2095
Temperature / °C Thermal conductivity / W·m⁻¹·K⁻¹ Specific heat / J·kg⁻¹·K⁻¹
20 24.60 458.8
200 26.25 518.5
500 27.30 587.8
600 27.76 726.2
800 28.07 905.4
850 28.39 1151.1

CAE setup. I imported the three-dimensional model into the preprocessor and created a mesh with more than 17 million cells. The casting and ingate were meshed with a fine grid, the runner and cooling channels were meshed with an intermediate grid, and the mold was meshed with a standard grid. This balanced accuracy and computation time. The boundary conditions and initial simulation parameters are summarized in Table 6. I tracked temperature at several points near the remote bearing hole and at the gate to determine when the pressure path was lost.

Parameter Value Parameter Value
Initial melt temperature 650 °C Slow-shot velocity 0.35 m/s
Initial mold temperature 180 °C High-speed velocity 3.5 m/s
Machine capacity 840 t High-speed interval 220 mm
Clamping time 12 s Intensification pressure 80 MPa
Environment temperature 20 °C Mold-mold heat transfer 3500 W/(m²·K)

Product and mold analysis. The engine bracket was a connection part between the engine and the subframe. It had a complex shape with many ribs and recesses. The wall thickness varied from about 3 mm to about 17 mm. The remote bearing hole was above the main parting plane, creating a local high point. This geometry prevented an effective vent from being placed at the last-filled position. I designed the initial mold with three ingates to promote stable filling and with overflow wells at the far end. However, the remote bearing hole still could not be vented well, and the local pressure could not be transmitted effectively after the gate solidified.

Filling simulation. The simulation showed that the total filling time from the beginning of shot-sleeve motion to complete cavity fill was about 2 s. The metal reached the ingate at about 1.943 s. The cavity fill time after that was about 54 ms. The remote bearing hole was the last region to fill, and the filling temperature there was about 636 °C. This temperature was lower than the temperature at the ingate and mid-cavity positions, so the local fluidity was lower, and the trapped gas could not be easily displaced. The metal at the mid-cavity positions was about 642–646 °C, while the ingate positions were about 648 °C.

Air pressure prediction. The predicted air pressure in most of the cavity was close to atmospheric pressure, which indicated generally acceptable venting for the main body. However, the region around the remote bearing hole reached a very high local air pressure because gas could not escape. This high-pressure gas pocket was the source of the casting defect. The simulation therefore predicted a gas porosity casting defect at the same location that was later observed in production trials.

Solidification simulation. The gate solidified at about 3 s after filling. After that, the intensification pressure could no longer be transmitted into the casting. The remote bearing hole remained in a semisolid or liquid state for a longer time because it was thicker than the surrounding thin walls. By about 8 s, the overall solid fraction reached about 98.88%. The local isolated liquid pool could not be fed, so a mixed gas-shrinkage casting defect formed. The simulation results are summarized in Table 7.

Stage Time Observation Implication for casting defect
Ingate arrival 1.943 s Metal enters cavity Filling starts smoothly
Complete filling about 2.0 s Remote hole fills last Gas is trapped near remote hole
Remote hole fill temperature about 636 °C Lower local fluidity Poor gas escape and poor feeding
Gate solidification about 3 s Pressure path is lost Intensification cannot feed remote hole
Final solid fraction about 8 s 98.88% solid Last region retains casting defect

Production verification. I produced the bracket on an 840 t cold-chamber die casting machine and inspected the castings with X-ray imaging and sectioning. The production casting defect matched the CAE prediction. The remote bearing hole showed a large gas pore. The maximum pore diameter before optimization was about 3.2 mm, and the local porosity was about 9.0%. According to the acceptance criteria, this casting defect was unacceptable. The result confirmed that the simulation was reliable enough to guide process optimization and local squeeze design.

Melt treatment. Before the casting trials, I melted the AlSi9Cu3 ingots in a centralized melting furnace and transferred the melt to a transfer ladle. I then performed degassing and deslagging with a rotary degassing unit. The degassing parameters were: feeding time 30 s, feeding speed 1.2 kg/min, feeding delay 30 s, degassing time 180 s, rotor speed 800 r/min for feeding, and rotor speed 480 r/min for degassing. The gas flow rate was kept above 1.5 m³/h. This step was important because hydrogen and oxide inclusions can also contribute to the casting defect. After degassing, I removed the oxide layer from the melt surface before pouring.

Taguchi optimization. I used an L9 orthogonal array to evaluate the effects of intensification pressure, high-speed velocity, and high-speed interval on the casting defect. The factors and levels are listed in Table 8. Each trial condition was run with three castings for X-ray measurement. Two discard castings were produced between different trial conditions to stabilize the process.

Trial Intensification pressure / MPa High-speed velocity / m/s High-speed interval / mm
A1 80 3.0 190
A2 80 3.5 200
A3 80 4.0 210
B1 90 3.0 190
B2 90 3.5 200
B3 90 4.0 210
C1 100 3.0 190
C2 100 3.5 200
C3 100 4.0 210

Taguchi results. The casting defect was reduced as intensification pressure increased and as high-speed velocity and high-speed interval were adjusted toward the middle of the window. The best condition among the conventional trials was C2: intensification pressure 100 MPa, high-speed velocity 3.5 m/s, and high-speed interval 200 mm. Under this condition, the maximum pore diameter was about 1.8 mm, and the local porosity was about 4.2%. This was better than the baseline but still above the acceptable level for the critical bearing region. The conventional process optimization therefore reduced the casting defect but did not eliminate it. The results are summarized in Table 9.

Trial Maximum pore diameter / mm Local porosity / % Relative casting defect level
A1 3.2 9.0 Severe
A2 1.9 6.8 High
A3 2.8 7.7 High
B1 3.1 8.6 Severe
B2 1.7 5.9 Moderate
B3 2.0 6.4 Moderate
C1 2.4 7.0 High
C2 1.8 4.2 Moderate
C3 1.8 4.5 Moderate

Why process optimization was insufficient. The conventional process variables controlled the global filling and solidification behavior, but they could not change the local geometry that trapped gas. The remote bearing hole remained a last-filled, poorly vented, and poorly fed region. Increasing the intensification pressure helped compress the pore, but the pressure path was lost when the gate solidified. Increasing the high-speed velocity helped fill the cavity quickly, but it also increased turbulence and gas entrapment. Decreasing the high-speed velocity reduced turbulence but increased the risk of cold shut. Therefore, the casting defect could not be fully removed by the global process window alone. A local intervention was required.

Local squeeze principle. Local squeeze is a process in which a pin applies pressure to a selected region while the metal is still in a semisolid state. The pressure compresses existing pores, breaks the oxide film around gas pores, and forces surrounding liquid metal into the pore volume. It also improves local feeding and increases local density. Unlike global intensification, local squeeze acts directly on the critical region, so it can reduce the casting defect even when the global pressure path is weak. The squeeze pressure is calculated from the hydraulic system pressure and the area ratio:

$$ P_{\text{squeeze}}=P_{\text{system}}\left(\frac{D_{\text{piston}}}{D_{\text{pin}}}\right)^2 $$

The force acting on the squeeze pin is:

$$ F_{\text{squeeze}}=P_{\text{squeeze}}\frac{\pi D_{\text{pin}}^2}{4} $$

For the engine bracket, the squeeze pin diameter was 10.5 mm, the hydraulic cylinder bore was 50 mm, and the system pressure was 16 MPa. The calculated squeeze pressure was about 360 MPa, and the force on the pin was about 31 kN. This pressure was high enough to compress the local casting defect but not so high that it caused cracking or sticking.

Local squeeze design. I converted the original core pin into a squeeze pin. The squeeze pin was made of SKD61 tool steel, heat treated to HRC 40–45, and then coated to increase surface hardness. The measured hardness after coating was about HRC 50–55. The squeeze pin diameter was 10.5 mm, and the clearance between the pin and the sleeve was kept between 0.02 and 0.04 mm. This clearance was small enough to prevent molten metal from entering the sleeve but large enough to allow smooth sliding. The front 15 mm of the sleeve was used as the guiding section, and the rear section was relieved to reduce friction. The squeeze stroke was set to 20 mm. The hydraulic cylinder was connected to the squeeze pin through upper and lower clamping rings, and the cylinder was fixed to the moving mold frame by connection plates. The sleeve was fixed by a locking plate to maintain alignment.

Local squeeze process sequence. The process sequence was as follows. First, the squeeze pin was retracted so that it did not block the cavity. The pin face was about 1–2 mm outside the cavity surface. Second, the cavity was filled by the HPDC shot. Third, after a delay time, when the local metal reached the semisolid state, the squeeze cylinder advanced the pin. Fourth, the pin held pressure for a set duration. Fifth, after the casting solidified, the squeeze pin retracted, and the casting was ejected. The delay time and duration were the most important parameters because they determined whether the local metal was soft enough to be compressed but solid enough not to be pushed away.

Semisolid window. For AlSi9Cu3, the liquidus temperature was about 580 °C, and the solidus temperature was about 480 °C. The solid fraction increased rapidly between these temperatures. A delay time that was too short left the metal too liquid; the squeeze pin could advance easily, but the pressure was not effectively retained. A delay time that was too long left the metal too solid; the squeeze pin could not advance, and the local casting defect remained. I used the CAE temperature history at the remote hole to estimate the semisolid window. At a delay time of about 1.0 s, the local temperature was about 560–570 °C, corresponding to a solid fraction of about 19–37%. This was the preferred window for local squeeze.

Delay-time experiment. I kept the squeeze pressure at 360 MPa and the squeeze duration at 0.5 s while varying the delay time from 0.1 s to 2.0 s. The measured squeeze depth decreased as the delay time increased. At 0.1 s, the depth was about 7.99 mm because the metal was still very liquid. At 1.0 s, the depth was about 4.80 mm. At 2.0 s, the depth dropped to about 0.56 mm because the metal had become too solid. The results are listed in Table 10. Based on these results, I selected a delay time of about 0.85–1.0 s for the local squeeze process.

Delay time / s Average squeeze depth / mm Local metal condition Squeeze effectiveness
0.10 7.99 Mostly liquid Low pressure retention
0.30 7.09 Liquid-rich Low pressure retention
0.50 6.04 Liquid-rich Moderate
0.75 5.25 Semisolid beginning Good
1.00 4.80 Semisolid Best
1.20 2.27 Solid-rich Reduced
1.50 0.99 Mostly solid Poor
2.00 0.56 Solid Poor

Duration experiment. I fixed the squeeze pressure at 360 MPa and the delay time at 1.0 s, and I varied the squeeze duration from 0.5 s to 5.0 s. The maximum pore diameter and local porosity both decreased as the duration increased. At 0.5 s, the maximum pore diameter was about 2.35 mm and the local porosity was about 4.3%. At 1.0 s, the maximum pore diameter was about 2.29 mm and the porosity was about 3.9%. At 3.0 s, the maximum pore diameter was about 1.41 mm and the porosity was about 1.2%. At 5.0 s, the maximum pore diameter was about 0.46 mm and the porosity was about 0.6%. A duration longer than 5 s caused the casting to stick to the squeeze pin during ejection, so I selected 5.0 s as the upper practical limit. The results are listed in Table 11.

Duration / s Average squeeze depth / mm Maximum pore diameter / mm Local porosity / % Casting defect level
0.5 4.80 2.35 4.3 Unacceptable
1.0 4.86 2.29 3.9 Unacceptable
1.5 5.01 1.97 2.9 Marginal
3.0 5.59 1.41 1.2 Acceptable
4.0 5.80 0.72 1.0 Acceptable
5.0 6.45 0.46 0.6 Level 1

Final process window. The final process window combined the best conventional parameters with the local squeeze parameters. The intensification pressure was 100 MPa, the high-speed velocity was 3.5 m/s, the high-speed interval was 200 mm, the squeeze pressure was 360 MPa, the squeeze delay time was 1.0 s, and the squeeze duration was 5.0 s. Under these conditions, the casting had a smooth surface and a sound internal structure. The maximum pore diameter was about 0.46 mm, and the local porosity was about 0.6%. This satisfied the level 1 acceptance criterion for the critical region. The final comparison is shown in Table 12.

Condition Maximum pore diameter / mm Local porosity / % Casting defect status
Baseline HPDC 3.2 9.0 Severe casting defect
Optimized HPDC 1.8 4.2 Improved but unacceptable
Local squeeze assisted HPDC 0.46 0.6 Level 1, acceptable

Mechanism of improvement. The local squeeze process improved the casting defect by two mechanisms. First, the mechanical pressure collapsed the gas pores and broke the oxide film around them. Second, the pressure forced the surrounding semisolid metal into the pore volume and improved local feeding. Because the squeeze pin acted directly on the last-filled region, it did not depend on the global pressure path through the gate. This was the key reason why local squeeze succeeded where global process optimization alone did not. The casting defect was not merely moved to another location; it was compressed and healed locally.

Tooling considerations. The squeeze pin and sleeve had to withstand high temperature and high pressure. I used a heat-treated and coated tool steel to resist wear and thermal fatigue. The clearance between the pin and sleeve was controlled to 0.02–0.04 mm. If the clearance was too large, molten metal could enter the sleeve and seize the pin. If the clearance was too small, thermal expansion could cause the pin to stick. The guiding length was limited to the front section, and the rear section was relieved to reduce friction. The squeeze pin stroke was 20 mm, which provided enough displacement for local compression without over-penetrating the casting. I also avoided setting the squeeze duration longer than 5 s because the casting could stick to the pin during ejection.

Process control. I integrated the squeeze cylinder into the die casting machine control system. The squeeze delay time started after the shot completion signal. The squeeze duration was controlled by a timer. The hydraulic pressure was set by a proportional valve. The squeeze pin returned after the casting solidified. I verified the sequence by checking the squeeze depth and the X-ray images. The process was repeatable when the delay time was held near 1.0 s and the duration was held near 5.0 s. The casting defect was consistently reduced in repeated trials.

Practical implications. The results showed that a casting defect in a complex HPDC part should not be treated only as a global process problem. Local geometry, local venting, and local pressure transmission can dominate the casting defect. CAE simulation is useful for locating the last-filled region and estimating the local temperature and solid fraction. Taguchi optimization is useful for finding a stable global process window. Local squeeze is useful for removing the remaining casting defect that global optimization cannot reach. The combination of these methods produced a robust process for the engine bracket.

Limitations. The local squeeze process required additional tooling and control. The squeeze pin was exposed to high temperature and could not be cooled as effectively as the main mold inserts. Over many cycles, thermal expansion and wear could reduce the clearance and cause sticking. In this study, I managed the risk by using a coated pin, a controlled clearance, and a limited squeeze duration. However, a dedicated cooling system for the squeeze pin would further improve tool life. A servo-controlled squeeze cylinder could also provide more precise motion and force control. These improvements would be valuable for high-volume production.

Conclusions. I studied the casting defect problem of an engine bracket produced by HPDC. The main conclusions are as follows.

First, the casting defect was caused by gas entrapment at the last-filled remote bearing hole and by insufficient feeding after the gate solidified. The high parting step and complex local geometry prevented effective venting and pressure transmission.

Second, CAE simulation predicted the casting defect location and mechanism. The predicted results agreed with production trials. The remote hole filled at about 636 °C, the gate solidified at about 3 s, and the final solid fraction reached about 98.88% after about 8 s. These results explained why global intensification could not eliminate the casting defect.

Third, Taguchi optimization showed that intensification pressure, high-speed velocity, and high-speed interval all influenced the casting defect. The best conventional condition was 100 MPa intensification pressure, 3.5 m/s high-speed velocity, and 200 mm high-speed interval. This reduced the maximum pore diameter from about 3.2 mm to about 1.8 mm and the local porosity from about 9.0% to about 4.2%. However, the casting defect remained unacceptable.

Fourth, I designed and implemented a local squeeze process. The squeeze pin diameter was 10.5 mm, the pin-sleeve clearance was 0.02–0.04 mm, the cylinder bore was 50 mm, and the squeeze stroke was 20 mm. The calculated squeeze pressure was about 360 MPa, and the force on the pin was about 31 kN.

Fifth, the local squeeze delay time and duration controlled the casting defect. A delay time of about 0.85–1.0 s placed the local metal in the semisolid state. A duration of 5.0 s provided enough time for pore compression and local feeding. The final process produced a maximum pore diameter of about 0.46 mm and a local porosity of about 0.6%, meeting the level 1 acceptance criterion.

Sixth, the combination of CAE, Taguchi optimization, and local squeeze formed an effective method for reducing the casting defect in the engine bracket. The method can be applied to other lightweight aluminum HPDC parts with local thick sections, remote holes, or difficult venting. The casting defect was reduced from a severe level to an acceptable level without changing the overall alloy system or abandoning HPDC.

Future work. I see several opportunities to extend this work. A local squeeze simulation model could be developed to predict the pore compression and local feeding behavior more directly. A dedicated cooling system for the squeeze pin could be designed to reduce thermal fatigue. A servo-controlled squeeze unit could be used to improve repeatability. The same local squeeze principle could also be transferred to other casting and molding processes where local shrinkage or gas entrapment causes a persistent casting defect. Overall, the results show that local squeeze assisted HPDC is a practical route for reducing casting defect severity and improving the mechanical integrity of complex aluminum components.

</f

Scroll to Top