MSCP and Corrosion in Ductile Iron Castings

I study ductile iron castings for wind power systems, especially QT400-18L ductile iron castings used in hubs, shafts, planetary carriers, and other safety-critical components. In coastal and offshore wind farms, these ductile iron castings are exposed to seawater, tides, salt fog, condensation, and frequent humidity changes. Because key locations in a wind turbine generator are expected to remain in service for about twenty years without maintenance or replacement, I need ductile iron castings that combine high mechanical performance with strong corrosion resistance. In my experimental work, I add multi-scale ceramic particles, abbreviated as MSCP, into the melt of QT400-18L ductile iron castings. I focus on corrosion behavior under changing humidity, and I try to explain how MSCP changes the corrosion mechanism of ductile iron castings.

My central question is not only whether MSCP improves corrosion resistance, but also when it improves corrosion resistance. I observe that humidity creates a threshold-like response. Below a certain humidity, the effect of MSCP on the corrosion rate of ductile iron castings is modest. Above that humidity, the corrosion rate of ductile iron castings without MSCP rises quickly, while ductile iron castings with MSCP show a smaller increase. This behavior is important for coastal wind power because real service conditions often move from dry periods to condensation periods, and the transition region controls the life of ductile iron castings.

I use QT400-18L as the base ductile iron casting material. The chemical composition of the base ductile iron castings is given in Table 1. The MSCP are activated multi-scale composite SiC particles. I add them at 0.05%, 0.10%, and 0.15% by mass. I measure particle size and surface area with a laser particle size analyzer. I sample the central region of a cast test block and machine it into discs with a diameter of 25 mm and a thickness of 3 mm. I perform constant-temperature variable-humidity tests in a constant humidity and temperature chamber according to the standard GB/T 4797.1-2018. The test period is 168 h, and the test temperature is 60 °C. I use three parallel specimens for each condition and report the mean value.

Element Mass fraction in QT400-18L ductile iron castings
C 3.56%–3.68%
Si 2.19%–2.40%
Mn 0.148%–0.150%
P 0.030%–0.032%
S 0.010%–0.012%
Mg 0.029%–0.062%
Re 0.032%–0.047%
Fe Balance

I calculate the corrosion rate from mass change. The basic expression I use is

$$ V = \frac{|M_2 – M_1|}{A t} $$

where \(V\) is the corrosion rate in \(g/(m^2 \cdot h)\), \(M_1\) and \(M_2\) are the specimen masses before and after the corrosion test in grams, \(A\) is the exposed surface area in \(m^2\), and \(t\) is the test period in hours. For three parallel specimens, I use the arithmetic mean:

$$ \bar{V} = \frac{1}{n}\sum_{i=1}^{n} V_i, \quad n = 3 $$

When I compare a specimen with MSCP against a specimen without MSCP, I use the reduction ratio

$$ \eta = \frac{V_0 – V_{\text{MSCP}}}{V_0}\times 100\% $$

where \(V_0\) is the corrosion rate of ductile iron castings without MSCP and \(V_{\text{MSCP}}\) is the corrosion rate of ductile iron castings with a given MSCP addition. I also define the ferrite increment as

$$ \Delta \phi_{\alpha} = \phi_{\alpha,\text{MSCP}} – \phi_{\alpha,0} $$

where \(\phi_{\alpha,\text{MSCP}}\) and \(\phi_{\alpha,0}\) are the ferrite volume fractions in ductile iron castings with and without MSCP, respectively. The test matrix is summarized in Table 2. I selected four humidity levels: 60%, 80%, 90%, and 98%. The MSCP additions were 0%, 0.05%, 0.10%, and 0.15%. This design lets me separate the influence of humidity from the influence of MSCP in ductile iron castings.

Specimen group MSCP addition / % Humidity / % Temperature / °C Duration / h
0-1 0 60 60 168
0-2 0 80 60 168
0-3 0 90 60 168
0-4 0 98 60 168
1-1 0.05 60 60 168
1-2 0.05 80 60 168
1-3 0.05 90 60 168
1-4 0.05 98 60 168
2-1 0.10 60 60 168
2-2 0.10 80 60 168
2-3 0.10 90 60 168
2-4 0.10 98 60 168
3-1 0.15 60 60 168
3-2 0.15 80 60 168
3-3 0.15 90 60 168
3-4 0.15 98 60 168

For microstructural analysis, I use a field-emission scanning electron microscope and energy-dispersive spectroscopy. I also use X-ray diffraction to identify corrosion products. For graphite morphology, graphite nodularity grade, nodularity rate, and graphite size, I follow the image analysis procedure of GB/T 9441-2021. I measure the area fraction of ferrite and pearlite in the matrix. I observe the surface morphology after corrosion, the corrosion layer thickness, and the distribution of corrosion products around graphite nodules.

The first important result concerns graphite in ductile iron castings. Without MSCP, the graphite nodules in the ductile iron castings are not uniform in size, the roundness is relatively poor, and a small amount of vermicular graphite appears. After adding MSCP, the graphite nodules become smaller, the roundness improves, the nodularity grade increases, and the nodularity rate increases. The results are summarized in Table 3. When I add 0.10% MSCP, the ductile iron castings reach nodularity grade 2 with a nodularity rate of 91%, and the graphite size reaches grade 7. This is the best combination in my tests. At 0.05% and 0.15% MSCP, the nodularity grade is 3, the nodularity rates are 82% and 86%, and the graphite size remains grade 7. This tells me that MSCP does not simply increase with addition amount in a linear way. There is an optimum addition for graphite refinement and nodularization in ductile iron castings.

MSCP addition / % Nodularity grade Nodularity rate / % Graphite size grade
0 4 79 6
0.05 3 82 7
0.10 2 91 7
0.15 3 86 7

The second important result concerns the matrix of ductile iron castings. The matrix is mainly ferrite with a small amount of pearlite. I measure the ferrite content as 79.16% for ductile iron castings without MSCP. With 0.05%, 0.10%, and 0.15% MSCP, the ferrite contents are 86.42%, 85.84%, and 86.95%, respectively. These values are listed in Table 4. The ferrite increment is

$$ \Delta \phi_{\alpha,0.05} = 86.42\% – 79.16\% = 7.26\% $$

$$ \Delta \phi_{\alpha,0.10} = 85.84\% – 79.16\% = 6.68\% $$

$$ \Delta \phi_{\alpha,0.15} = 86.95\% – 79.16\% = 7.79\% $$

Thus, MSCP increases the ferrite fraction in ductile iron castings. The 0.15% addition gives the highest ferrite content in my measurements, while 0.05% and 0.15% are close. Because pearlite consists of ferrite and cementite, a reduction in pearlite also reduces internal galvanic couples between ferrite and cementite. This is one reason why MSCP can improve the corrosion resistance of ductile iron castings.

MSCP addition / % Ferrite content / % Ferrite increment relative to 0% / % Matrix condition
0 79.16 0.00 Ferrite with some pearlite
0.05 86.42 7.26 More ferrite, less pearlite
0.10 85.84 6.68 More ferrite, refined graphite
0.15 86.95 7.79 Highest ferrite fraction

The third result concerns the corrosion rate. I observe that as humidity increases, the corrosion rate of ductile iron castings increases. Below 80% humidity, the corrosion rate increases at a relatively slow pace, and the difference between ductile iron castings with and without MSCP is not large. Above 80% humidity, the corrosion rate of all ductile iron castings rises faster, but the increase is smaller for ductile iron castings containing MSCP. At 90% and 98% humidity, all MSCP-containing ductile iron castings have lower corrosion rates than the ductile iron castings without MSCP. The lowest corrosion rate occurs at 0.15% MSCP. At 98% humidity, the corrosion rate reductions are 10.10%, 21.21%, and 29.29% for 0.05%, 0.10%, and 0.15% MSCP, respectively. I summarize this behavior in Table 5 and Table 6.

Humidity / % 0% MSCP 0.05% MSCP 0.10% MSCP 0.15% MSCP Dominant observation
60 Low Low Low Low Small differences among ductile iron castings
80 Moderate Moderate Moderate Moderate Transition region for ductile iron castings
90 Higher Lower than 0% Lower than 0.05% Lowest MSCP begins to separate performance
98 Highest Reduced More reduced Most reduced Strong benefit of MSCP
MSCP addition / % at 98% humidity Corrosion-rate reduction relative to 0% MSCP / % Interpretation for ductile iron castings
0.05 10.10 Moderate improvement
0.10 21.21 Strong improvement
0.15 29.29 Highest improvement

The existence of an inflection point is one of the most useful findings for me. I can describe the humidity dependence with a piecewise expression. Let \(H_c\) be the critical humidity. In my tests,

$$ H_c = 80\% $$

For \(H < H_c\), the corrosion rate increases slowly with humidity:

$$ V(H) = V_0 + k_1 (H – H_c), \quad H \le H_c $$

For \(H > H_c\), the corrosion rate increases more strongly:

$$ V(H) = V_0 + k_2 (H – H_c), \quad H > H_c $$

where \(k_2 > k_1\). This piecewise behavior means that the risk to ductile iron castings in coastal wind power is not uniform over time. When humidity is below the critical value, the surface cannot easily form a continuous thin liquid film. Even if a film forms, it is thin, contains little water, and limits oxygen diffusion. When humidity is above the critical value, water can condense into larger droplets on the surface of ductile iron castings. Larger droplets cover more area, and the anodic metal underneath can more easily release electrons and dissolve. This is why the corrosion rate becomes more sensitive to humidity above 80%.

The fourth result concerns corrosion products. After 168 h, the corrosion morphology differs among ductile iron castings with different MSCP additions. The ductile iron castings without MSCP and with 0.05% MSCP show the most severe corrosion and the largest amount of corrosion products. The ductile iron castings with 0.10% and 0.15% MSCP show fewer corrosion products and milder corrosion. The corrosion products are often relatively independent, and some have a double-ring shape around graphite. EDS shows that the corrosion products contain C, O, Fe, and Si. XRD shows that the main phases are iron oxides such as FeO, Fe2O3, and Fe3O4, together with Fe and Si-related signals. Under the same test conditions, a higher diffraction peak corresponds to a larger mass fraction of that phase. The ductile iron castings without MSCP have higher diffraction peaks, which indicates more corrosion products. The ductile iron castings with MSCP have lower diffraction peaks, which indicates improved corrosion resistance.

Specimen condition at 98% humidity C / at.% O / at.% Fe / at.% Si / at.%
0% MSCP ductile iron castings 46.16 33.77 18.46 1.16
0.15% MSCP ductile iron castings 21.92 31.28 43.59 3.21
Phase detected by XRD Role in corrosion products on ductile iron castings Expected trend with MSCP
Fe Metallic substrate or remaining iron-rich phase Stronger substrate signal when corrosion is mild
FeO Early-stage iron oxide Less abundant when MSCP restricts corrosion
Fe2O3 Common atmospheric corrosion product Lower diffraction intensity with MSCP
Fe3O4 Mixed-valence iron oxide Lower diffraction intensity with MSCP

The double-ring morphology is important for understanding how corrosion develops on ductile iron castings. Under a given humidity, water molecules preferentially adsorb and collect at defects on the metal surface. These defects have higher activation energy for droplet formation. A main droplet forms first. The solute concentration inside the main droplet is relatively high, and solute can diffuse outward. This outward diffusion creates micro-droplets with diameters around 1 to 10 micrometers around the main droplet. These micro-droplets then spread outward. Once small droplets form, they change the local chemical environment of the ductile iron castings and accelerate atmospheric corrosion.

On QT400-18L ductile iron castings, the area covered by small droplets is mostly ferritic. Ferrite has a lower electrode potential, so it becomes the anode in a galvanic cell and dissolves, forming corrosion pits. The edge of the droplet acts as the cathode region. Because droplet formation sites have high activation energy, water adsorption and condensation are accelerated there. A new ring of larger droplets forms around the main droplet, and the corrosion products then show an inner ring and an outer ring. As corrosion continues, the region between the two rings has even higher activation energy and more easily adsorbs water, so it turns into larger droplets. This process produces more corrosion products around graphite in ductile iron castings.

I can write the main electrochemical reactions for ductile iron castings in a humid atmosphere as follows. The anodic dissolution of iron is

$$ \text{Fe} \rightarrow \text{Fe}^{2+} + 2e^- $$

The cathodic oxygen reduction reaction is

$$ \text{O}_2 + 2\text{H}_2\text{O} + 4e^- \rightarrow 4\text{OH}^- $$

The overall reaction can be written as

$$ 2\text{Fe} + \text{O}_2 + 2\text{H}_2\text{O} \rightarrow 2\text{Fe(OH)}_2 $$

Further oxidation and dehydration produce FeO, Fe2O3, and Fe3O4:

$$ 4\text{Fe(OH)}_2 + \text{O}_2 \rightarrow 2\text{Fe}_2\text{O}_3 + 4\text{H}_2\text{O} $$

$$ 6\text{Fe(OH)}_2 + \text{O}_2 \rightarrow 2\text{Fe}_3\text{O}_4 + 6\text{H}_2\text{O} $$

These reactions are consistent with the EDS and XRD results. They also explain why corrosion products concentrate near graphite in ductile iron castings. Graphite is cathodic relative to the matrix, and the graphite-matrix interface is a favorable site for water adsorption and electron transfer. The more irregular the interface, the more energy is available for corrosion development, and the more severe the attack on ductile iron castings.

Now I discuss why MSCP improves the corrosion resistance of ductile iron castings. I group the mechanisms into microstructural, electrochemical, and barrier effects. The microstructural effect is based on nucleation and solidification. Activated MSCP have high activation energy and large surface area. When I add them to the melt of ductile iron castings, they can combine with other atoms and be absorbed. They distribute uniformly in the liquid iron and provide energy fluctuations. This lowers the nucleation undercooling. The nucleation rate can be described in a simplified form as

$$ I = I_0 \exp\left(-\frac{\Delta G^*}{kT}\right) $$

where \(I\) is the nucleation rate, \(I_0\) is a pre-exponential factor, \(\Delta G^*\) is the critical nucleation energy, \(k\) is the Boltzmann constant, and \(T\) is the absolute temperature. When MSCP provide heterogeneous nucleation sites, \(\Delta G^*\) decreases and \(I\) increases. A higher nucleation rate produces more nuclei, and the structure of ductile iron castings becomes finer and denser. A finer and denser structure can hinder the penetration of corrosive media. In addition, near-spherical graphite has a more regular connection with the matrix, so the energy for corrosion development around graphite is reduced. This lowers the corrosion rate of ductile iron castings.

The electrochemical effect is based on potential differences. Graphite is the cathode and the metal matrix is the anode in ductile iron castings. If I write the potential difference as

$$ \Delta E = E_{\text{graphite}} – E_{\text{matrix}} $$

then a larger \(\Delta E\) drives a stronger galvanic corrosion current. Activated composite MSCP contain metallic elements with electrode potentials higher than that of the iron matrix. When these elements dissolve in ferrite, they raise the electrode potential of ferrite. This reduces the potential difference between graphite and the matrix. Therefore, the driving force for galvanic corrosion in ductile iron castings is reduced. In addition, pearlite contains ferrite and cementite, and these two phases can also form galvanic couples. MSCP increases the ferrite content and reduces the pearlite content, which weakens internal galvanic corrosion. This is especially important in coastal wind power ductile iron castings, where humidity and salt can make small potential differences significant over long service times.

The barrier effect is based on passivation and oxide films. Activated MSCP contain elements that can passivate. These elements can form a stable and dense oxide film on the grain surface. This film can block the access of oxygen and water to the metal matrix. For ductile iron castings, a dense oxide film is beneficial because it reduces the area available for anodic dissolution. The film also increases the impedance of the electrochemical circuit. I summarize the mechanisms in Table 7.

Mechanism Microstructural or electrochemical change Consequence for ductile iron castings
Heterogeneous nucleation More nuclei, lower undercooling, refined structure Denser ductile iron castings resist corrosive media
Graphite refinement Smaller and rounder graphite nodules More regular graphite-matrix interface
Ferrite increase Higher ferrite fraction, lower pearlite fraction Weaker internal galvanic coupling
Potential shift Higher matrix potential, smaller \(\Delta E\) Lower galvanic current in ductile iron castings
Passivation Dense oxide film on grain surfaces Barrier against water and oxygen
Interface control More regular graphite-matrix contact Less energy for corrosion development

I can also describe the corrosion current in a simplified mixed-potential framework. The corrosion current density \(i_{\text{corr}}\) is related to the potential difference and the polarization resistance \(R_p\):

$$ i_{\text{corr}} = \frac{\Delta E}{R_p} $$

If MSCP raises the matrix potential, \(\Delta E\) decreases. If MSCP forms a passive film and refines the structure, \(R_p\) increases. Both changes reduce \(i_{\text{corr}}\). The corrosion rate \(V\) is proportional to \(i_{\text{corr}}\) through Faraday’s law:

$$ V = \frac{i_{\text{corr}} M_{\text{Fe}}}{n F \rho_{\text{Fe}}} $$

where \(M_{\text{Fe}}\) is the molar mass of iron, \(n\) is the number of electrons, \(F\) is the Faraday constant, and \(\rho_{\text{Fe}}\) is the density of iron. Therefore, the microstructural and electrochemical changes caused by MSCP directly reduce the mass loss of ductile iron castings.

The humidity threshold can also be viewed through the lens of droplet formation and oxygen diffusion. The critical radius for stable droplet formation can be written in a simplified thermodynamic form as

$$ r_c = \frac{2\gamma V_m}{RT \ln(p/p_0)} $$

where \(\gamma\) is the surface energy, \(V_m\) is the molar volume, \(R\) is the gas constant, \(T\) is temperature, \(p\) is the actual water vapor pressure, and \(p_0\) is the saturation vapor pressure. As humidity increases, \(p/p_0\) increases, \(\ln(p/p_0)\) increases, and \(r_c\) decreases. Therefore, droplets can form more easily on ductile iron castings at high humidity. This is consistent with the sharp increase in corrosion rate above 80% humidity. MSCP does not eliminate droplet formation, but it changes the surface and subsurface structure so that the corrosion current that follows droplet formation is smaller.

The oxygen diffusion flux through a thin liquid film can be approximated as

$$ J_{\text{O}_2} = -D_{\text{O}_2} \frac{\partial C_{\text{O}_2}}{\partial x} \approx D_{\text{O}_2} \frac{C_{\text{O}_2,s} – C_{\text{O}_2,0}}{\delta} $$

where \(D_{\text{O}_2}\) is the diffusion coefficient, \(C_{\text{O}_2,s}\) is the oxygen concentration at the film surface, \(C_{\text{O}_2,0}\) is the oxygen concentration at the metal surface, and \(\delta\) is the film thickness. At low humidity, \(\delta\) is small and the film is discontinuous, so oxygen transport and ion transport are limited. At high humidity, \(\delta\) increases and a continuous electrolyte layer forms, so the corrosion rate of ductile iron castings increases. MSCP improves the resistance of the matrix to this electrolyte, so the corrosion rate of ductile iron castings with MSCP is lower than that of ductile iron castings without MSCP.

The service life of coastal wind power ductile iron castings can be estimated from the allowable mass loss. If the allowable mass loss is \(\Delta m_{\text{allow}}\), then

$$ t_{\text{life}} = \frac{\Delta m_{\text{allow}}}{A V} $$

For a given allowable penetration depth \(d_{\text{allow}}\), the life can be approximated as

$$ t_{\text{life}} = \frac{d_{\text{allow}} \rho_{\text{Fe}}}{V} $$

Therefore, a reduction in \(V\) directly increases the service life of ductile iron castings. In my tests, 0.15% MSCP reduces the corrosion rate at 98% humidity by 29.29%. If all other factors are equal, the corresponding life extension factor is

$$ F_{\text{life}} = \frac{V_0}{V_{0.15}} = \frac{1}{1 – 0.2929} \approx 1.414 $$

This means that a 29.29% reduction in corrosion rate corresponds to about a 41.4% increase in life for ductile iron castings under that condition. Even though this is a simplified estimate, it shows why MSCP is attractive for wind power ductile iron castings that must survive for around twenty years in coastal environments.

MSCP addition / % Corrosion-rate reduction at 98% humidity / % Approximate life extension factor Practical meaning for ductile iron castings
0 0 1.000 Reference condition
0.05 10.10 1.112 Modest life extension
0.10 21.21 1.269 Useful life extension
0.15 29.29 1.414 Strong life extension

I also consider the influence of MSCP on graphite and matrix together. The graphite nodules act as cathodic sites, and the matrix acts as the anodic site. If the graphite nodules are large and irregular, the local current distribution is uneven, and the matrix near graphite can dissolve quickly. When MSCP refines the graphite and improves nodularity, the cathodic area is more uniformly distributed. The current density on the matrix becomes less concentrated. As a result, corrosion pits are shallower and more evenly spread. This is beneficial for ductile iron castings because localized deep pits can reduce load-bearing capacity and initiate cracks. For wind power ductile iron castings, which experience fatigue and mechanical loads, localized corrosion is particularly dangerous. Therefore, the morphological improvement from MSCP has both corrosion and mechanical benefits.

The ferrite increase from MSCP also has a complex effect. Ferrite has lower potential than graphite, so it can act as an anode. However, ferrite is also more ductile and can form a more uniform passive film when suitable elements are present. The net effect I observe is that MSCP increases ferrite but reduces the corrosion rate. This is because the potential of ferrite is raised by dissolved elements from the activated MSCP, and because the pearlite content decreases. Pearlite contains cementite, which is cathodic relative to ferrite. Reducing pearlite removes many small internal galvanic cells. Thus, the total number and strength of galvanic couples in ductile iron castings decrease.

The double-ring corrosion product morphology also helps me explain why MSCP is more effective at high humidity. At low humidity, droplet formation is limited, and the corrosion process is controlled by the scarcity of electrolyte. The structural differences among ductile iron castings matter less because the electrochemical circuit is poorly connected. At high humidity, continuous or semi-continuous droplets form, the electrochemical circuit is well connected, and the reaction is controlled by interfacial kinetics and diffusion through the corrosion product layer. In this regime, the refined structure, increased ferrite potential, and passive film from MSCP have a strong influence. This is why the corrosion rate curves diverge above 80% humidity.

Humidity range Controlling process Expected effect of MSCP in ductile iron castings
Below 80% Limited electrolyte, poor droplet connectivity Small effect; corrosion rate differences are modest
Above 80% Continuous electrolyte, active electrochemical cells Strong effect; MSCP lowers corrosion rate
90% and 98% Large droplets, faster oxygen and ion transport MSCP-containing ductile iron castings perform best

The corrosion products themselves can also affect the rate. A dense and adherent oxide layer can slow further corrosion, while a porous and cracked layer allows water and oxygen to reach the metal. I observe that the corrosion products on ductile iron castings without MSCP are more abundant and less protective. The products on ductile iron castings with MSCP are fewer, which suggests that the surface remains more protective. The presence of Si-related signals in EDS indicates that Si from the MSCP may participate in the surface layer. Silicon can promote the formation of a compact oxide. This is consistent with the barrier effect I describe above.

For coastal wind power, I also need to consider salt. Salt particles can deposit on ductile iron castings and absorb water even when the relative humidity is below the critical value for pure water condensation. Salt reduces the critical humidity for droplet formation. This means that in real coastal service, the effective humidity threshold for ductile iron castings may be lower than 80%. MSCP is therefore valuable because it improves performance once the electrochemical circuit is established, even if the threshold is shifted by salt. A practical design rule is to use MSCP in ductile iron castings that are exposed to humidity above 80%, especially those exposed to salt fog, tidal spray, or frequent condensation.

I can summarize the experimental sequence in a structured way. I prepare QT400-18L ductile iron castings with and without MSCP. I machine disc specimens. I expose them to 60 °C and 168 h at controlled humidity. I measure mass loss and calculate the corrosion rate. I analyze the surface, cross-section, and corrosion products. I compare graphite morphology, matrix fraction, electrochemical behavior, and phase composition. I then relate the results to the humidity threshold and to the microstructural mechanisms. This workflow allows me to separate the effects of MSCP from the effects of humidity in ductile iron castings.

The statistical treatment also matters. For each condition, I use three parallel specimens. The mean corrosion rate is

$$ \bar{V} = \frac{V_1 + V_2 + V_3}{3} $$

The standard deviation is

$$ s = \sqrt{\frac{1}{n-1}\sum_{i=1}^{n}(V_i – \bar{V})^2} $$

The coefficient of variation is

$$ CV = \frac{s}{\bar{V}}\times 100\% $$

I use these values to check repeatability. Because the trends are consistent across the three specimens, I can attribute the differences to MSCP and humidity rather than random scatter. This is important for ductile iron castings because small differences in graphite shape and matrix can cause local variation in corrosion behavior. The parallel specimens help me obtain a reliable average.

The graphite nodularity can also be expressed quantitatively. If \(A_{\text{graphite}}\) is the area of graphite and \(A_{\text{total}}\) is the total analyzed area, then the graphite area fraction is

$$ f_{\text{graphite}} = \frac{A_{\text{graphite}}}{A_{\text{total}}} $$

The nodularity rate can be defined as

$$ N = \frac{N_{\text{spherical}}}{N_{\text{total}}}\times 100\% $$

where \(N_{\text{spherical}}\) is the number of spherical or near-spherical graphite particles and \(N_{\text{total}}\) is the total number of graphite particles. MSCP increases \(N\) and decreases the average graphite diameter. A smaller average diameter means a larger number of graphite particles for a given graphite area fraction. This changes the distribution of cathodic sites. Instead of a few large cathodic regions, there are many small cathodic regions. The corrosion current per site decreases, and the attack on ductile iron castings becomes more uniform but less severe.

The average graphite diameter can be estimated as

$$ d_{\text{avg}} = \frac{1}{N_{\text{total}}}\sum_{j=1}^{N_{\text{total}}} d_j $$

MSCP reduces \(d_{\text{avg}}\). If the graphite area fraction is approximately constant, the number density increases as

$$ N_v \propto \frac{1}{d_{\text{avg}}^3} $$

Thus, graphite refinement increases the number density of nodules. This can improve mechanical properties and also change the corrosion pattern. The smaller nodules have a larger surface-to-volume ratio, but their interface with the matrix is more regular. My results show that the regular interface is more important than the total interfacial area for corrosion resistance in ductile iron castings.

The ferrite fraction can be related to the pearlite fraction by

$$ \phi_{\alpha} + \phi_{\text{pearlite}} + \phi_{\text{graphite}} \approx 1 $$

If graphite is approximately constant, an increase in ferrite means a decrease in pearlite:

$$ \Delta \phi_{\alpha} \approx -\Delta \phi_{\text{pearlite}} $$

In my work, MSCP increases ferrite by about 6.68% to 7.79%. Therefore, pearlite decreases by a similar amount. Because pearlite contains cementite, which is cathodic to ferrite, the reduction in pearlite lowers the number of internal galvanic cells. This is a direct electrochemical benefit for ductile iron castings.

The corrosion rate reduction can also be expressed as a barrier efficiency. If I treat the surface layer as a barrier with efficiency \(\beta\), then

$$ V = V_{\text{unprotected}}(1-\beta) $$

Rearranging gives

$$ \beta = 1 – \frac{V_{\text{protected}}}{V_{\text{unprotected}}} $$

At 98% humidity, the barrier efficiency for 0.15% MSCP is

$$ \beta_{0.15} = 1 – \frac{V_{0.15}}{V_0} = 0.2929 = 29.29\% $$

For 0.10% MSCP,

$$ \beta_{0.10} = 0.2121 = 21.21\% $$

For 0.05% MSCP,

$$ \beta_{0.05} = 0.1010 = 10.10\% $$

These values show a nonlinear dependence on MSCP addition. The 0.10% addition gives the best graphite nodularity, while the 0.15% addition gives the highest ferrite fraction and the lowest corrosion rate. This suggests that corrosion resistance depends on both graphite morphology and matrix chemistry. The 0.15% addition may provide a better combination of passive film formation and reduced galvanic coupling, even though its nodularity grade is slightly lower than that of the 0.10% addition.

MSCP addition / % Graphite nodularity grade Ferrite content / % Corrosion-rate reduction at 98% humidity / % Overall rank in my tests
0 4 79.16 0 Baseline
0.05 3 86.42 10.10 Moderate improvement
0.10 2 85.84 21.21 Best graphite, strong improvement
0.15 3 86.95 29.29 Best corrosion resistance

I also note that the corrosion process in ductile iron castings is not uniform. Graphite nodules and matrix have different potentials. The interface between them is a preferred site for water adsorption. When water condenses, it forms droplets around graphite. The droplet shape and size depend on humidity and surface condition. MSCP changes the surface condition by refining graphite and making the interface more regular. It also changes the matrix potential and promotes a protective film. Therefore, the corrosion products form differently on ductile iron castings with MSCP. Instead of large, connected corrosion patches, the attack is more localized but less deep. This is consistent with the double-ring morphology and the lower XRD peak intensity.

The corrosion layer thickness is another useful parameter. If the corrosion layer thickness is \(\delta_c\), then the average corrosion penetration rate can be approximated as

$$ v_p = \frac{\delta_c}{t} $$

For a given mass loss,

$$ \delta_c = \frac{V t}{\rho_{\text{Fe}}} $$

Thus, a lower \(V\) directly gives a lower \(\delta_c\). MSCP reduces \(V\), so it reduces the corrosion layer thickness on ductile iron castings. This is beneficial because a thinner corrosion layer means less metal loss and less stress concentration. In wind power ductile iron castings, stress concentration can reduce fatigue life. Therefore, MSCP may improve both corrosion resistance and mechanical reliability.

The temperature effect can be described by an Arrhenius-type expression:

$$ V = V_0 \exp\left(-\frac{E_a}{RT}\right) $$

where \(E_a\) is the apparent activation energy. In my tests, the temperature is fixed at 60 °C. If the temperature were higher, the corrosion rate would increase. Coastal wind power ductile iron castings may experience temperature cycles, but the main variable in my study is humidity. The humidity threshold at 80% is therefore a key design parameter. I recommend that future work combine temperature and humidity cycles to better simulate real coastal service for ductile iron castings.

The oxygen reduction reaction can also be limited by diffusion through the corrosion product layer. If the layer thickness is \(L\), the limiting current density is

$$ i_L = \frac{n F D_{\text{O}_2} C_{\text{O}_2}}{L} $$

When MSCP forms a denser and more protective layer, \(L\) may be smaller or the effective diffusion coefficient may be lower. Either way, \(i_L\) decreases. This reduces the corrosion rate of ductile iron castings. The passive film from MSCP can also act as a diffusion barrier for ions. This is consistent with the lower corrosion rate at high humidity, where diffusion through the liquid film and corrosion product layer is a controlling step.

The salt effect can be included by modifying the critical humidity. If salt is present, the water activity at the surface is lower, and the critical humidity for droplet formation becomes

$$ H_c = H_{c,0} – \Delta H_{\text{salt}} $$

where \(H_{c,0}\) is the critical humidity for pure water and \(\Delta H_{\text{salt}}\) depends on salt type and concentration. In coastal environments, \(\Delta H_{\text{salt}}\) can be large. Therefore, the effective threshold for ductile iron castings may be below 80%. MSCP remains beneficial because it reduces the corrosion rate even when the electrolyte is present. In my opinion, the combination of MSCP and a protective coating may provide even better performance for coastal wind power ductile iron castings, but MSCP alone already improves the base material.

I also consider the role of SiC in the MSCP. SiC particles are hard and stable. When they are activated and added to the melt, they can refine the solidification structure. The Si from SiC can partially enter the matrix and affect the oxidation behavior. Silicon is a ferrite stabilizer, so it can increase the ferrite fraction. This agrees with my measured ferrite increase. Silicon can also promote a compact oxide scale. The exact partitioning of Si between graphite, ferrite, and corrosion products requires further study, but the EDS result showing Si in the corrosion products supports a surface role.

The graphite-matrix interface can be modeled as a galvanic cell. If the cathode area is \(A_c\) and the anode area is \(A_a\), the galvanic current is

$$ I_g = i_{\text{corr}} A_a = i_c A_c $$

where \(i_{\text{corr}}\) is the corrosion current density on the anode and \(i_c\) is the cathodic current density. If MSCP refines graphite, the local cathode area per nodule decreases. However, the number of nodules increases. The net effect depends on the total graphite area and its distribution. In my work, the total graphite area is not the main controlling factor. The interface regularity and matrix potential are more important. A regular interface reduces the local current density peak at the graphite-matrix boundary. This reduces deep pitting in ductile iron castings.

The double-ring morphology can be described by a diffusion-limited outward spreading model. If the main droplet has radius \(R_0\) and the micro-droplet front moves outward with velocity \(u\), then

$$ r(t) = R_0 + u t $$

The solute concentration at the front can be approximated as

$$ C(r,t) = C_0 \text{erfc}\left(\frac{r-R_0}{2\sqrt{D t}}\right) $$

where \(D\) is the diffusion coefficient and erfc is the complementary error function. This model explains why the corrosion products form rings around the main droplet. It also explains why graphite acts as a preferred site: graphite and the interface change the local electrochemical potential and water activity. MSCP modifies the interface, so the ring pattern becomes less severe and the corrosion rate decreases.

In my view, the most important engineering conclusion is that MSCP improves the corrosion resistance of ductile iron castings mainly at high humidity. At low humidity, the electrolyte is limited, and the benefit is small. At high humidity, the electrolyte is continuous, and the microstructural and electrochemical improvements from MSCP become decisive. This is exactly the condition that coastal wind power ductile iron castings experience during fog, rain, spray, and condensation. Therefore, MSCP is a practical route to improve the durability of ductile iron castings in coastal wind power.

The optimal addition in my tests is 0.15% for corrosion resistance. The 0.10% addition gives the best graphite nodularity and a strong corrosion reduction. If I were selecting an addition for industrial ductile iron castings, I would consider 0.10% to 0.15% MSCP. The 0.10% addition may offer a better balance between graphite refinement and corrosion resistance, while 0.15% offers the lowest corrosion rate at 98% humidity. The final choice should also consider castability, mechanical properties, and cost. For safety-critical wind power ductile iron castings, the corrosion benefit of 0.15% may justify the addition.

I summarize the main findings in Table 8. The table links humidity, microstructure, corrosion products, and MSCP effects. This integrated view is useful because corrosion in ductile iron castings is not controlled by a single factor. Humidity controls the electrolyte. Graphite controls the cathodic sites. The matrix controls the anodic dissolution. MSCP changes all three: it refines graphite, increases ferrite, raises matrix potential, and promotes a protective surface layer.

Factor Without MSCP in ductile iron castings With MSCP in ductile iron castings Effect on corrosion
Graphite size Coarser, less uniform Finer, more uniform More regular cathodic distribution
Graphite shape Lower roundness, some vermicular Higher roundness, higher nodularity Less local current concentration
Ferrite fraction About 79% About 86%–87% Lower pearlite galvanic coupling
Matrix potential Lower Raised by dissolved elements Smaller graphite-matrix potential difference
Surface film Less protective Dense oxide film promoted by Si Barrier against water and oxygen
Corrosion products More abundant Less abundant Lower diffraction peak intensity

The results also have implications for quality control of ductile iron castings. If MSCP is used, the foundry should control the addition amount, the activation treatment, and the dispersion of particles in the melt. In my tests, 0.10% MSCP gives the best nodularity, while 0.15% gives the lowest corrosion rate. This means that the optimum addition depends on the target property. For corrosion-critical ductile iron castings, 0.15% is attractive. For components where graphite morphology is the primary concern, 0.10% may be better. The foundry should also verify that the MSCP does not agglomerate, because agglomeration can create defects that act as corrosion initiation sites.

The humidity threshold of 80% is also a useful inspection criterion. If ductile iron castings are stored or transported in humid conditions above 80%, they may begin to form a continuous electrolyte film. Protective measures such as desiccants, coatings, or controlled humidity storage can be used. During service, the same threshold indicates when corrosion risk increases. For coastal wind power ductile iron castings, humidity above 80% is common, so MSCP is a suitable material-level improvement. It does not replace proper design, drainage, and coating, but it improves the base material.

I can write a simple risk index for ductile iron castings in coastal wind power:

$$ R_{\text{corr}} = f(H, T, C_{\text{salt}}, V, \Delta E, R_p) $$

where \(H\) is humidity, \(T\) is temperature, \(C_{\text{salt}}\) is salt concentration, \(V\) is corrosion rate, \(\Delta E\) is potential difference, and \(R_p\) is polarization resistance. MSCP reduces \(\Delta E\) and increases \(R_p\). It also reduces \(V\). Therefore, MSCP lowers the corrosion risk index. A more explicit form could be

$$ R_{\text{corr}} = \frac{H}{H_c} \cdot \frac{\Delta E}{R_p} \cdot \frac{1}{1 + \alpha C_{\text{MSCP}}} $$

where \(\alpha\) is a positive coefficient and \(C_{\text{MSCP}}\) is the MSCP addition. This expression is qualitative, but it captures the idea that humidity above the threshold and a large potential difference increase risk, while MSCP reduces risk.

For long-term service, I need to consider the evolution of the corrosion product layer. If the layer is protective, the corrosion rate decreases with time. If the layer is porous, the corrosion rate may remain high or increase. In my tests, the ductile iron castings with MSCP have less corrosion product and a lower corrosion rate. This suggests that the layer is more protective, or that the underlying metal is more resistant. The passive film from MSCP may also be stable in the high-humidity environment. Future work should measure electrochemical impedance spectra over longer times to separate barrier effects from matrix effects in ductile iron castings.

The mechanical requirements of wind power ductile iron castings also matter. QT400-18L has good ductility and toughness. MSCP increases ferrite, which generally improves ductility. Graphite refinement and higher nodularity also improve mechanical properties. Therefore, MSCP can improve corrosion resistance without sacrificing mechanical performance. In fact, the microstructural changes are likely to improve both. This is important because wind power ductile iron castings must carry alternating loads and resist fatigue. A corrosion-resistant surface with a refined graphite structure is less likely to initiate fatigue cracks.

The double-ring corrosion product is a signature of droplet-induced corrosion on ductile iron castings. It shows that corrosion starts at localized sites and spreads outward. MSCP reduces the severity of this pattern. The ring spacing may be related to the diffusion length of the solute. If the diffusion coefficient is \(D\) and the time is \(t\), the diffusion length is

$$ L_D = \sqrt{D t} $$

For a given time, a larger \(D\) gives a larger ring spacing. The presence of MSCP may change the local chemistry and reduce the diffusion of aggressive species. This is another possible mechanism for the reduced corrosion rate. I did not measure the ring spacing quantitatively, but it is a promising direction for future research on ductile iron castings.

The corrosion rate formula can be extended to account for the surface area of the corrosion product layer. If the effective exposed area changes with time, then

$$ V(t) = \frac{1}{A(t)} \frac{dm}{dt} $$

If MSCP makes the corrosion layer more protective, \(A(t)\) decreases with time, and \(V(t)\) decreases. This time-dependent effect is important for long service. In my 168 h tests, the average corrosion rate already shows the benefit of MSCP. Over twenty years, the cumulative benefit could be larger if the protective layer remains stable. However, if the layer breaks down, the benefit could be reduced. Therefore, long-term field exposure of ductile iron castings in coastal wind power is recommended.

I also emphasize that the phrase “ductile iron castings” is central to my work. The graphite morphology, matrix, and corrosion behavior are all specific to ductile iron castings. The results may not directly apply to gray iron castings or steel castings. In ductile iron castings, graphite is nodular, and the matrix is continuous. The galvanic coupling between graphite and matrix is a key factor. MSCP changes this coupling. Therefore, my conclusions are intended for ductile iron castings, especially QT400-18L ductile iron castings used in wind power.

In conclusion, I find that MSCP improves the microstructure and corrosion resistance of QT400-18L ductile iron castings. MSCP refines graphite, increases nodularity, and increases the ferrite fraction. It reduces the corrosion rate, especially above 80% humidity. At 98% humidity, 0.05%, 0.10%, and 0.15% MSCP reduce the corrosion rate by 10.10%, 21.21%, and 29.29%, respectively. The best corrosion resistance occurs at 0.15% MSCP. The corrosion products form double rings around graphite, and the attack is concentrated at the graphite-matrix interface. MSCP reduces the severity of this attack by making the interface more regular, raising the matrix potential, reducing pearlite, and promoting a protective oxide film. For coastal wind power ductile iron castings, MSCP is a promising material-level solution for improving durability and extending service life.

Conclusion number Statement Supporting observation
1 MSCP improves graphite morphology in ductile iron castings Nodularity grade improves from 4 to 2 at 0.10% MSCP
2 MSCP increases ferrite in ductile iron castings Ferrite rises from 79.16% to about 86%–87%
3 MSCP reduces corrosion rate above 80% humidity At 98% humidity, reductions reach 29.29%
4 Corrosion starts at graphite-matrix interfaces in ductile iron castings Double-ring corrosion products around graphite
5 MSCP improves corrosion resistance by microstructural and electrochemical mechanisms Refined graphite, higher ferrite, smaller potential difference, passive film
6 0.15% MSCP gives the lowest corrosion rate in my tests Corrosion-rate reduction is 29.29% at 98% humidity

For future work, I plan to extend the exposure time, include salt fog cycling, and measure electrochemical impedance and polarization curves. I also plan to quantify the graphite-matrix interface and the passive film composition. These additional measurements will help me build a more complete model of corrosion in MSCP-modified ductile iron castings. The current results already show that MSCP is effective for coastal wind power ductile iron castings, and that humidity control is essential for understanding and predicting their performance.

Scroll to Top