Inoculation treatment of nodular cast iron automobile steering knuckle
In addition to melting, the inoculation treatment of nodular cast iron is also a key link in the quality of […]
News
News
Choosing the Right Gate Valve: Factors to Consider for Optimal Performance
When selecting a gate valve for your application, several factors should be considered to ensure optimal performance and reliability. Here
News
Permanent Mold Casting vs. Other Casting Methods: Comparing Strengths and Limitations
Permanent mold casting, also known as gravity die casting, is a casting method that involves the use of reusable molds
News
Chemical composition control of ductile iron castings automobile steering knuckle
The material grade of the used steering knuckle is QT450-10, and its chemical composition mainly includes C, Si, Mn, S,
News
Non-shrinkage casting process design of nodular cast iron automobile steering knuckle
1. Structural analysis and technical requirements of automobile steering knuckle The automobile steering knuckle has complex curved surface, large cross-section
News
Non-shrinkage casting process of ductile iron castings automobile steering knuckle
As the connection between the wheel and suspension system, the steering knuckle in the automobile chassis parts bears the load
Scientific
Trial Production of Ductile Iron Castings Parts for Split Gearbox
The comparison of validation results of the three process schemes is shown in the table. Overall, Scheme III has certain
Scientific
Casting Process Plan of Ductile Iron Castings for Split Gearbox
In order to eliminate the shrinkage cavity and porosity defects caused by solidification shrinkage of molten iron, take the relatively
News
Casting Technology Analysis of Ductile Iron Castings of Split Gearbox
Ductile iron castings have paste solidification characteristics and are easy to produce dispersed shrinkage porosity. If there is high sand
Scientific
Casting Technology of Nodular Cast Iron Parts for Split Gearbox
The nodular cast iron parts of the split gear box are obtained by machining the upper and lower gear boxes
News
Causes, Types, and Solutions of Casting Defects
Casting defects refer to irregularities or imperfections that occur during the casting process, resulting in undesirable qualities in the final
News
Innovations in Globe Valve Technology: Advancements in Flow Control
In recent years, there have been several innovations in globe valve technology aimed at enhancing flow control and improving overall
Scientific
Lightweight Casting Process Design of Ductile Iron Metro Gear Box
1. Chemical composition The ability of liquid metal to fill the mold cavity and obtain spheroidal graphite cast iron with
News
Lightweight structure design of nodular cast iron metro gear box
The lightweight of nodular cast iron metro gear box requires structural optimization at first. Under the condition that the main
News
Lightweight technology of ductile iron castings metro gear box
The gear box is an important part of the power transmission of metro vehicles. During the operation of the vehicle,
News
Improvement of Casting Process Plan for Ductile Iron Drive Wheel
After the trial production of the sample, the tooth anatomy was verified. The shrinkage defect at the center of the
News
ProCAST casting simulation of nodular cast iron driving wheel
After the process design of nodular cast iron, ProCAST was used for process simulation, and the results showed that there
News
Gravity Casting Parts
Chapter 1: The Basic Principles of Gravity Casting Gravity casting, also known as permanent mold casting, is a metal casting
News
Trial production of a high strength graphite cast iron cylinder
With the improvement of domestic engine emission standards and the demand of high-power engines, the traditional gray cast iron cylinder
News
Analysis of Hot Crack Tendency in Lost Foam Casting Box-Behnken Test
When the stress or deformation in the lost foam casting exceeds the strength limit or strain capacity of the alloy
News
Analysis of Box-Behnken Test Results in Lost Foam Casting
The optimal process parameter combination of lost foam casting valve body is simulated by ProCAST software, and the other parameters
Scientific
Box-Behnken Experimental Design of Lost Foam Casting
These process factors, such as pouring temperature, pouring speed, vacuum degree and mold temperature, have an impact on the molding
News
Lost Wax Casting vs. Other Casting Methods: Comparing Strengths and Limitations
Lost wax casting, also known as investment casting, is a casting method known for its ability to produce intricate and
News
Effect of Pouring Speed in Lost Foam Casting
The influence of different pouring speeds in lost foam casting is shown in the figure. When the pouring speed is
News
Effect of pouring temperature on lost foam casting
The influence of different pouring temperatures is shown in Figure 1. Pouring temperature has certain influence on lost foam casting,
News
Top and side pouring of valve body lost foam casting
The gating system of lost foam casting is different from the traditional sand casting, and should be as simple as
Scientific
Boundary Conditions and Thermophysical Parameters of Valve Body lost foam casting
Through the model established by SolidWorks software, the MeshCAST module in ProCAST software can be imported for mesh division and
Scientific
Geometric model of valve body lost foam casting
The lost foam casting material of high-pressure valve body is carbon steel ZG230-450, with good toughness and plasticity and excellent
News
Custom Sand Casting Parts: Tailored Solutions for Specific Industry Needs
Custom sand casting parts provide tailored solutions to meet specific industry needs. With sand casting, manufacturers can produce highly customizable
Scientific
Control equation of mold filling in lost foam casting
During the filling process of lost foam casting, the flow of liquid metal must meet the hydrodynamic laws, which can