Research status of ht350 high strength gray cast iron in China and abroad
The output data of castings of various materials in China in 2010, including 29.5 million tons of cast iron, 9.9 […]
News
News
Wind power nodular cast iron castings
The nodular cast iron accessories of wind power mainly include the wheel hub, main shaft seat, gearbox, torque arm and
Scientific
Fracture defect of guide wheel of sand casting excavator
Through the analysis of the failed parts by the method of factor diagram, the reasons for the fracture of the
News
Nodular cast iron for wind power castings
Since its emergence, nodular cast iron has been widely used in the production of cast iron pipe fittings, auto parts,
News
Cast low alloy bainite wear resistant steel excavator shovel teeth
Most of the shovel teeth of roadheader work in the environment of high impact, high wear and high hardness, so
Scientific
Simulation of sand casting scheme for rear axle housing
(1) Mold filling simulation analysis. Figure 1 and Figure 2 are the simulation diagrams of sand casting at 7.5 s
News
Setting of pretreatment parameters for sand casting
(1) Task setting: select sand casting, mold filling analysis and heat / solidification analysis before and after mold filling. (2)
News
Fault detection of bucket teeth of mining excavator
The bucket of mining excavator is the main working part of excavator equipment. Its bucket teeth consume a lot in
Scientific
Determination of pouring position in sand casting
The pouring position of sand mold casting is the position of the casting in the mold during pouring. It directly
News
Sand casting of steel castings for excavator rear axle housing
The design of sand casting process plays a key role in the quality of castings. The traditional process design of
Scientific
Defects in sand casting process of rear axle housing
The sand casting process adopts two box molding and furan resin sand molding and core making. The diameter of the
News
Heat transfer coefficient of solidification interface of sand casting
ZL105 aluminum alloy has low density, high strength and good casting properties. It has been applied to automobile, machine tool,
News
Rapid sand casting of engine cylinder head
Through the research, a complete process route of rapid sand mold casting is obtained. ① ugnx8 0 software to establish
Scientific
Numerical simulation results of sand mold gravity casting scheme
The working environment of engine cylinder head in the engine is poor, which needs to bear high thermal load and
Scientific
Analysis of sand casting process of cylinder head
According to the analysis of sand casting process, the design of three gating systems is put forward. The influence of
News
Top Sand Casting Companies and Their Signature Techniques
Several top sand casting companies are renowned for their expertise and signature techniques: These companies distinguish themselves through their specialized
Scientific
Design of graphical user interface for bucket tooth recognition system
Graphical user interface (GUI) refers to the interface that is convenient for users to operate the computer through graphics to
News
Residual heat normalizing of nodular cast iron crankshaft
Casting waste heat normalizing is a process method of normalizing with the help of residual temperature after casting solidification. The
Scientific
Analysis of mold filling process of sand castings
For the second Pouring Scheme of cylinder head, the temperature field distribution of symmetrical top injection inner gate during mold
News
Experiment on bucket teeth of bimetal liquid composite casting
1.Experimental device This experiment is carried out on the self-made hydraulic simulation test-bed in the laboratory. The cast bucket tooth
Scientific
Sand core design and parting of sand castings
Firstly, the sand core design and block processing of the model are carried out. At the same time, the block
Scientific
Measurement of sand casting and mold temperature
The temperature cooling curve of sand castings in phenolic urethane resin sand is shown in the figure. From figure (a),
Scientific
Mold filling and solidification simulation of lost foam casting process scheme for top injection cast steel valve body
(1) Simulation results and analysis of mold filling process Figure 1 (a) – (f) shows the change process of mold
News
Medium manganese steel and ultra-high manganese steel
Under low impact load, the wear resistance of medium manganese steel is better than that of high manganese steel. The
News
Casting technology and properties of sand casting cylinder head
According to the sand mold casting process CAD system developed by the laboratory, the casting process design is carried out.
Scientific
Design of riser in sand casting
The riser is to compensate for the possible shrinkage during the formation of sand castings, prevent the shrinkage cavity and
News
Numerical simulation of mold filling and solidification process of cylinder head in rapid sand casting
With the development of economy, China’s automobile industry has developed rapidly, but it is facing the problems of unreasonable industrial
News
Design of gating system in sand casting
The gating system of sand casting is used to guide the liquid metal into the mold cavity. According to the
Scientific
Three dimensional geometric modeling of engine cylinder head in sand casting
Ugnx8 0 software to model the three-dimensional model of sand casting engine cylinder head. UG NX is a new generation
News
Sand casting engine cylinder head
The casting blank of automobile engine cylinder head produced by sand mold gravity casting is shown in Figure 2-1. ZL105