Analysis of mold filling process of sand castings
For the second Pouring Scheme of cylinder head, the temperature field distribution of symmetrical top injection inner gate during mold […]
Scientific
News
Experiment on bucket teeth of bimetal liquid composite casting
1.Experimental device This experiment is carried out on the self-made hydraulic simulation test-bed in the laboratory. The cast bucket tooth
Scientific
Sand core design and parting of sand castings
Firstly, the sand core design and block processing of the model are carried out. At the same time, the block
Scientific
Measurement of sand casting and mold temperature
The temperature cooling curve of sand castings in phenolic urethane resin sand is shown in the figure. From figure (a),
Scientific
Mold filling and solidification simulation of lost foam casting process scheme for top injection cast steel valve body
(1) Simulation results and analysis of mold filling process Figure 1 (a) – (f) shows the change process of mold
News
Medium manganese steel and ultra-high manganese steel
Under low impact load, the wear resistance of medium manganese steel is better than that of high manganese steel. The
News
Casting technology and properties of sand casting cylinder head
According to the sand mold casting process CAD system developed by the laboratory, the casting process design is carried out.
Scientific
Design of riser in sand casting
The riser is to compensate for the possible shrinkage during the formation of sand castings, prevent the shrinkage cavity and
News
Numerical simulation of mold filling and solidification process of cylinder head in rapid sand casting
With the development of economy, China’s automobile industry has developed rapidly, but it is facing the problems of unreasonable industrial
News
Design of gating system in sand casting
The gating system of sand casting is used to guide the liquid metal into the mold cavity. According to the
Scientific
Three dimensional geometric modeling of engine cylinder head in sand casting
Ugnx8 0 software to model the three-dimensional model of sand casting engine cylinder head. UG NX is a new generation
News
Sand casting engine cylinder head
The casting blank of automobile engine cylinder head produced by sand mold gravity casting is shown in Figure 2-1. ZL105
Scientific
Prediction of defects in cold lap casting
The defect of cold lap casting is due to the fact that the unit solid rate at the flow front
Scientific
Prediction of casting defects with inclusions
According to the state and velocity of the flowing high-temperature metal liquid after colliding with each other in the mold
News
The Economic Role of China casting industry
The China casting industry plays a significant role in the country’s economy and has considerable influence on the global manufacturing
Scientific
Prediction of shrinkage porosity and cavity casting defects by critical solid rate method
Shrinkage cavity and porosity casting defect is a hole that occurs when the temperature of molten metal decreases during solidification
News
Casting technology of engine cylinder head
The engine is known as the “heart” of the automobile, and the cylinder head is one of the most important,
News
Functional design of bucket tooth detection system for excavator
According to the general requirements of the bucket tooth detection system of excavator, the functions of the designed detection system
News
Austempered nodular cast iron crankshaft
The full name of isothermal quenching is austenitic isothermal quenching. Austenitic isothermal quenched ductile iron (add) is obtained from nodular
News
Study on mold filling process of iron mold sand coated casting and cooling analysis of nodular cast iron crankshaft
(1) The process characteristics and heat transfer mode of iron mold sand coated casting are analyzed. Aiming at the common
News
Bimetallic liquid composite casting bucket teeth
Bucket tooth is a vulnerable part on the excavator bucket. When in use, the bucket tooth handle must have sufficient
Scientific
Experimental results of bimetallic liquid composite casting bucket teeth
(1) When the liquid level of molten iron with viscosity V1 is high, the flow state of molten steel into
News
Nodular cast iron crankshaft castings
As one of the important parts of the engine, the force of the crankshaft is complex in work. The constant
News
Heat treatment process of automobile piston pin
By the end of June 2019, the total number of motor vehicles in China had reached 357 million. With the
News
Alloyed high manganese steel
Ordinary high manganese steel has less work hardening and insufficient wear resistance under low stress wear or small impact load.
Scientific
Mold filling and solidification simulation of lost foam casting process scheme for bottom cast steel valve body
(1) Simulation results of mold filling process Figure 1 (a) – (f) shows the change process of mold filling temperature
News
Wear failure mechanism of bucket teeth of excavator
1. Cutting mechanism When the bucket tooth acts with the rock (ore) under high impact load, on the one hand,
News
Improve the wear resistance of bucket teeth and prolong the service life
(1) Composition optimization and material selection of wear-resistant materials high manganese steel can achieve high hardness due to work hardening,
News
Water based lost foam casting coating for cast iron
Lost foam casting technology has the advantages of wide application range, accurate size and shape of lost foam casting, smooth
News
Testing method of steel castings
1) For small and medium-sized castings (especially investment precision castings), they have small volume, light weight and less processing capacity.