The engine cylinder block and cylinder head produce casting sand holes
Sand hole is also a common defect of cylinder block (cylinder head) casting, which is often found on the upper […]
News
Scientific
Introduction of numerical simulation method for filling and solidification process of casting
Numerical simulation of casting filling is to analyze the heat transfer phenomenon and forming ability of high temperature liquid metal
News
The main factors of cracks in aluminum alloy wheel during low pressure casting
For the same alloy, whether the hub cracks or not often depends on the hub structure, process parameters and mold
News
Surface casting defects of die casting (part 1)
1 casting strain (1) characteristics: ① Along the opening direction, the surface of the casting shows a line like scratch
News
Sand casting – machine modeling
Machine modeling — the molding machine completes the main actions of sand filling, compaction and touching during the molding process.
News
The explanation of the type of gating system in casting process
(1) According to the position of the choke section A closed gating system The closed gating system refers to the
Scientific
Rapid sand casting technology of engine cylinder head based on numerical simulation
China’s automobile industry is booming and has become the pillar industry of national economic development. However, China’s automobile industry still
News
Prevention methods of non spheroidizing or bad spheroidizing defects of ductile iron parts
Features: the fracture surface of the casting is gray black, and the mechanical properties are obviously low. Through metallographic examination,
Scientific
Carbon emission source and evaluation boundary of sand casting production system
1. Carbon emission source of sand casting production system A large amount of waste gas produced by sand casting production
News
The history and development of foundry technology in China
Casting is the process of melting metal into a liquid that meets certain requirements and pouring it into the mold.
News
Design of gating system and inner runner in casting process
Gating system design： 1.Design of sprue cup (1) Sprue cup shape The shape of sprue cup can be divided into
Scientific
Research status of rapid sand casting at home and abroad
Rapid Prototyping technology relies on the point by point accumulation forming of materials, which is not restricted by the manufacturability
News
Analysis of common defects in castings
Casting porosity This is a small cavity formed by the gas which can not escape during the solidification of metal.
News
Sand casting – hand molding
Manual modeling definition – all modeling operations completed by hand or hand tools are called manual modeling. Advantages and disadvantages:
News
Design of casting process parameters
1.Casting shrinkage There are many factors that affect the casting shrinkage, such as the type and composition of the alloy,
News
Engine cylinder block and cylinder head produce casting porosity
Porosity is usually the most common defect in cylinder block castings, which often takes the first place in the scrap
News
Design of sand core for parts casting
The design of sand core is very important in the casting process, which directly affects the dimensional accuracy of castings
News
Common measuring tools for sand casting
1 tape measure: Used to measure length. 2 steel ruler: It is a common measuring tool for measuring length, outer
News
Selection of parting surface for casting parts
Parting surface refers to the surface on which two half molds contact each other. In addition to the solid casting
News
Causes of crack formation in aluminum alloy wheel during low pressure casting
Low pressure casting can realize high mechanization and automation, not only improve the productivity (10-15 type / h), but also
News
Common repair tools for sand casting
In order to make the sand mold (core) qualified, the defects of the sand mold (core) should be repaired with
News
Determination of pouring position of sand casting
The pouring position of casting refers to the position of casting in the mold during pouring. The determination of pouring
News
Common tools for sand casting
Common modeling tools are as follows. 1 shovel:Also known as shovel, it is used to shovel and mix sand (core).
News
Investigation on quality assurance system of nuclear power valve casting manufacturer
The buyer of the casting should not only pay attention to the quality of the casting itself, but also the
News
Application of sand casting technology in valve production
The quality of mold (core) sand has a great influence on the quality of casting. For example, the defects of
News
Casting and core making method of product parts
1.Manual core making (clay sand, synthetic grease, resin sand) Manual core making is suitable for simple and small batch castings.
News
Casting pattern and core box for sand casting
The mold used to obtain the shape of the casting is called pattern, and the mold used to obtain the
News
Characteristics and problems of valve casting process
Casting features: 1.Casting has a wide range of adaptability, great flexibility, product requirements and various working conditions. It can manufacture
News
Influence factors of die casting defects
Thinking of solving die casting defects Because the causes of each defect come from many different influencing factors, so in
News
Overview of valve casting in China
Casting is the process of pouring liquid metal into a mold cavity which is suitable for the shape of the