Sand casting bridge shell casting technology shrinkage of bridge shell
The linear shrinkage of the bridge shell has a great influence on the accuracy of the size of the bridge […]
News
News
Determination of pouring temperature for sand casting axle housing
Generally speaking, the higher the pouring temperature is, the better the fluidity of alloy liquid is, and the more favorable
Scientific
Calculation of spheroidization rate of nodular cast iron plunger pump
Spheroidization rate is one of the important and often used evaluation criteria of ductile iron. The calculation method is as
News
Determination of parting surface for sand casting axle housing
For sand mold casting, in order to realize sand molding, mold taking, pouring riser setting and sand core installation, the
Scientific
Graphite characteristic analysis of nodular cast iron plunger pump block
Based on the national standard GB / T 9441-2009 metallographic examination of nodular cast iron, the following four parameters are
News
Determination of casting position of axle housing in sand casting
The pouring position usually refers to the position of the axle housing in the mold when pouring. The pouring position
Scientific
Experimental scheme of nodular cast iron plunger pump block
In order to avoid too many times of Nitrocarburizing on different parts of lzqt600-3 ductile iron profile, the difficulty of
News
Composition requirements of main casting accessories for sand casting axle housing
For cast steel, the main raw materials include scrap steel, ferrosilicon, manganese iron and aluminum alloy deoxidizer, and the main
Scientific
Preparation of cylinder block of nodular cast iron plunger pump
During the production of lzqt600-3 ductile iron profile, due to its inherent process characteristics, the molten iron after spheroidizing treatment
News
Selection of raw materials for sand casting axle housing
(1) Scrap steel is the main raw material for casting smelting. Two samples are randomly selected from each batch for
Scientific
Air tightness test of sand casting axle housing
Air tightness test, also known as sealing test, is an important indicator to judge whether there is internal defect in
News
Design requirements and structure analysis of sand casting axle housing
The structural types of axle housing can be roughly divided into three types: open type, integral type and combined type.
Scientific
Inspection of axle housing section in sand casting
In order to verify the feasibility of casting process, the sample of open axle housing was trial produced according to
News
Process analysis and process parameters determination of casting structure of axle housing
The structural design of the axle housing can be roughly divided into the following aspects: the functional design of the
Scientific
Comparison and analysis of optimization design results of gating system for sand casting axle housing
After adding riser and chill to the gating system, mesh division, casting parameters setting and pouring process simulation calculation are
News
Research on sand mold casting technology of tractor axle housing
Taking the tractor split axle housing as the research object, the paper firstly analyzes the process of the overall structure
Scientific
Optimization design of chill for sand casting axle housing
The cold iron is directly attached to the area where the riser is not suitable. Because of the chilling effect
News
Main quality problems of casting axle housing
At present, most companies use sodium silicate sand mold casting and V-method casting process for production. In view of the
Scientific
Design of riser for sand casting axle housing
The ratio of the volume of the axle housing divided by the heat transfer surface area is called the solidification
News
Main research contents of sand mold casting technology for tractor open axle housing
As the key part of tractor, the main research contents are as follows: firstly, analyze the process of axle housing
Scientific
Analysis and comparison of shrinkage and porosity solidification defects of molten metal in sand casting axle housing
Shrinkage cavity is a common casting defect, which is essentially a volume defect. According to the causes, it can be
News
Development prospect of casting simulation technology
Since the 21st century, solidification numerical simulation technology has been developing continuously, and it is in the stage of optimization
Scientific
Temperature field simulation of molten metal in sand casting axle housing
Simulation and analysis of temperature field in closed gating system of axle housing The simulation of temperature field is shown
News
Present situation of casting technology at China and abroad
In foreign countries, the analysis unit of “heat and mass flow analyzer” of Columbia University was first used in casting
Scientific
Analysis of liquid metal filling process in semi closed gating system of sand casting axle housing
During pouring, under the action of gravity, the molten metal first enters the cavity through the sprue, enters the runner
News
Research status of casting simulation in China
Casting belongs to liquid metal forming technology. In actual production, casting engineers often make process according to previous experience, and
Scientific
Analysis of the filling process of the open casting system for sand casting bridge shell
Figures (a) and (b) show the flow of the liquid metal in the bridge shell when the metal liquid fills
News
Sand mold casting technology of tractor axle housing
A certain type of broken axle housing of a company is mainly used for tractor load-bearing bridge, with an annual
News
Correlation between Austempered Ductile Iron and its tensile properties
Several tensile test bars with the sizes of Φ 7mm × 90mm, Φ 12mm × 100mm and Φ 17mm ×
Scientific
Analysis of metal filling process in closed gating system of sand casting axle housing
Figure (a) is the real-time screenshot of the molten metal just filling the runner at the beginning of pouring, and