Effect of casting defects on strength of hydraulic valve body
With hydraulic valve body as carrier, the filling and solidification process of valve body casting were studied by combining theoretical […]
Scientific
Scientific
Scientific
Failure Analysis of Cast Hydraulic Valve Body
Hydraulic valves are subjected to complex and variable loads during their operation. Therefore, the strength of the valve body must
Scientific
Strength calculation and analysis of ideal hydraulic valve body before improvement
As one of the key components in the hydraulic transmission system, the working environment of the hydraulic valve is extremely
Scientific
Numerical simulation of casting process of hydraulic valve body
Based on one hydraulic valve body and two hydraulic multi way valve body, the design method of casting and pouring
Scientific
Load on cast hydraulic valve casting body
Hydraulic casting valve is the main component of hydraulic system, which controls the pressure, flow and direction of oil in
Scientific
Numerical simulation of casting defect formation of improved valve body
In the process of casting simulation, the pouring system, grid division and calculation conditions are the same as the above,
Scientific
Mathematical model of casting filling process
The filling process of liquid metal is a non-isothermal flow process with heat loss and solidification.The metal fluid flow should
Scientific
Common casting defects of cast hydraulic valve body
The main valve holes of multi-way valves, change-over valves and other valves are thin, with many oil grooves and different
Scientific
Using the blank of gate valve body to process block valve
1.Selection of gate valve body blank This method is suitable for the high pressure self tight seal gate valve body
Scientific
Casting Process Optimization of Bed Castings
Based on the analysis of simulation results, the casting process needs to be optimized to eliminate the casting solidification defects.
Scientific
Geometric model of cast hydraulic valve body
As a high load precision mechanical part, the hydraulic valve body has the requirements of high pressure resistance, fatigue resistance
Scientific
Solid fraction analysis during liquid metal solidification of casting bed parts
Because hot joints will occur in large and thick parts during the cooling process of castings, and casting defects such
Scientific
Thermo mechanical fatigue fracture analysis of cast ti-48al-2cr-2nb alloy
The fracture morphology of the cast ti-48al-2cr-2nb alloy with total strain range δ ε (T) = ± 0.7% and service
Scientific
Analysis of Temperature Field during Liquid Metal Solidification of Cast Bed Parts
After filling, in order to analyze casting problems such as subsequent solidification defects, the solidification temperature field is further analyzed.
Scientific
Model meshing and initial parameter setting for casting bed part production
Introduce the model into ProCast software and divide it into grid. After dividing the grid, check the quality of the
Scientific
Cast Ti-48Al-2Cr-2Nb Alloy Samples and Test Methods
Cylindrical billets are cut lengthwise on a 100 mm diameter billet and processed into equal-section samples with a working section
Scientific
Production Analysis of Casting Bed Parts
The net weight of machine tool body parts is 1762.75 kg, and the overall contour size of parts is 1985
Scientific
Structure and material of casting bed
Machining centers are divided into horizontal and vertical machining centers according to the position relationship between the spindle and the
Scientific
Corrosion resistance of high nickel ductile iron
The surface of high nickel ductile iron samples during corrosion process was observed. The results are similar to that of
Scientific
Corrosion resistance of high silicon molybdenum ductile iron
By observing the surface of the sample during the corrosion process, no obvious bubbles were found on the surface of
Scientific
Kinetics Analysis of High Nickel Ductile Iron Oxidation at High Temperature
The unit area gain of high nickel ductile iron at 900 C for different working hours is recorded in Figure
Scientific
Kinetics Analysis of High Temperature Oxidation of High Silicon Molybdenum Ductile Iron
The prepared sample is heated in a resistance furnace and weighed with an electronic balance.Figure 1 shows the measurement results
Scientific
Observation of Microstructure Change of High Silicon Molybdenum Ductile Iron at High Temperature
In order to understand the oxidation conditions at the cracks, elemental analyses are carried out on the areas of Fig.
Scientific
Macro Observation Result of Thermal Fatigue Resistance Test of Ductile Iron
The sample size for thermal fatigue test is 15 mm x 10 mm x 10 mm.To eliminate the influence of
Scientific
Effect of Thermal Cycle Temperature Gradient on Thermal Fatigue Crack of Ductile Iron
The temperature range of the thermal cycle (T) is equal to the upper limit temperature of the thermal cycle (T)
Scientific
Balance test of casting impeller
1. Selection and determination of detection method As a key part of the pump body, the impeller of desulfurization pump
Scientific
Application Technology of Steering Knuckle for Automotive Parts
1. Application of Tool Composite Technology In the process of steering knuckle of automobile parts, tool compound technology has outstanding
Scientific
Analysis of simulation results of casting process for automobile gasket
1. Filling Process Analysis The filling process simulation analysis of Figure 5 shows that the filling time of the casting
Scientific
Liquid metal filling process for casting bed parts
The flow of liquid metal in filling process has a great influence on the quality of casting. If the design
Scientific
Design of impeller blade in lost foam casting
The surface of the blade of the sulfur pump impeller and the surface of the blade are calculated to achieve